manualshive.com logo in svg

Lionel GG1, Руководство пользователя

Поделиться
Скачать
Lionel GG1 Скачать руководство пользователя страница 12

RailSounds 5.0 sound system operations

Installing the battery

A

lthough the RailSounds sound system is powered through the track, we recommend that
you install a nine-volt alkaline battery to prevent the sound system from shutting down

during track power interruptions (for example, at a switch or a dirty section of track). Follow
these steps and refer to Figure 4 as you install the battery.

If the RailSounds sound system turns off during interruptions in track power, you
may need to replace the battery.

1. Lift away the rear removable roof-top hatch.

2. Remove the protective cover from the battery harness.

3. Snap the battery harness onto the nine-volt alkaline battery’s terminals.

4. Slide the battery into the battery clip.

5. Replace the hatch. Two magnets secure the hatch to the roof.

The roof hatches serve as your locomotive’s antenna. Be sure that the hatches are in
place before operating your locomotive in the TrainMaster Command Control
environment.

12

Rear roof-top hatch (TMCC antenna)

Note!

Battery harness

Battery holder

Figure 4. Battery installation

Note!

REAR

FRONT

Содержание GG1





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды