Lionel ES44AC Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 36

background image

34

Replacing the traction tires

Maintaining and servicing your locomotive

Y

our locomotive is equipped with traction tires to increase the tractive effort of your locomotive and
allow it to pull more cars at once.

During the course of normal operations, the traction tires may become worn out. To replace the
traction tires, remove the side frame screws from the underside of the trucks and lift away the side
frame. See Figure 9. Remove the worn tire, then slip the replacement around the wheel. Reposition the
side frame on the truck and secure it with the two screws.

Side frame screws

Traction tires

Figure 9. Traction tire replacement

«
...
32
33
34
35
36
»

Содержание ES44AC





































Отзывы:

Нет отзывов

Похожие инструкции для ES44AC

Бренд: Landoll Страницы: 52

Бренд: JBSYSTEMS Light Страницы: 14

Бренд: JB Systems Страницы: 7

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Бренд: 3A HEALTH CARE Страницы: 16

Short/cut 2000 Audio Editor

Бренд: 360 Systems Страницы: 4

Бренд: NEILPRYDE Страницы: 53

Бренд: JAC Страницы: 103

Бренд: 3Disc Страницы: 12

Litmann Quality 3100

Бренд: 3M Страницы: 2

Бренд: HABYS Страницы: 16

Бренд: Tascam Страницы: 8

Бренд: IBEX Страницы: 4

Бренд: lancer Страницы: 3

Бренд: lancer Страницы: 12

Бренд: R2 Страницы: 26

TRAKTOR KONTROL S4

Бренд: Native Instruments Страницы: 86

Бренд: Native Instruments Страницы: 245

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды