background image

Linx Technologies
159 Ort Lane
Merlin, OR, US 97532

3090 Sterling Circle Suite 200
Boulder, CO 80301

Phone: +1 541 471 6256
Fax: +1 541 471 6251

www.linxtechnologies.com

Disclaimer

Linx Technologies is continually striving to improve the quality and function of its products.  For this reason, we 
reserve the right to make changes to our products without notice. The information contained in this Data Guide 
is believed to be accurate as of the time of publication. Specifications are based on representative lot samples. 
Values may vary from lot-to-lot and are not guaranteed. “Typical” parameters can and do vary over lots and 
application. Linx Technologies makes no guarantee, warranty, or representation regarding the suitability of any 
product for use in any specific application. It is the customer’s responsibility to verify the suitability of the part for 
the intended application. 

NO LINX PRODUCT IS INTENDED FOR USE IN ANY APPLICATION WHERE THE SAFETY 

OF LIFE OR PROPERTY IS AT RISK.

Linx Technologies

 

DISCLAIMS ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 

PURPOSE. IN NO EVENT SHALL LINX TECHNOLOGIES BE LIABLE FOR ANY OF CUSTOMER’S INCIDENTAL OR 
CONSEQUENTIAL DAMAGES ARISING IN ANY WAY FROM ANY DEFECTIVE OR NON-CONFORMING PRODUCTS 
OR FOR ANY OTHER BREACH OF CONTRACT BY LINX TECHNOLOGIES. 

The limitations on Linx Technologies’ 

liability are applicable to any and all claims or theories of recovery asserted by Customer, including, without 
limitation, breach of contract, breach of warranty, strict liability, or negligence. Customer assumes all liability 
(including, without limitation, liability for injury to person or property, economic loss, or business interruption) for all 
claims, including claims from third parties, arising from the use of the Products. The Customer will indemnify, 
defend, protect, and hold harmless Linx Technologies and its officers, employees, subsidiaries, affiliates, 
distributors, and representatives from and against all claims, damages, actions, suits, proceedings, demands, 
assessments, adjustments, costs, and expenses incurred by Linx Technologies as a result of or arising from any 
Products sold by Linx Technologies to Customer. Under no conditions will Linx Technologies be responsible for 
losses arising from the use or failure of the device in any application, other than the repair, replacement, or refund 
limited to the original product purchase price. Devices described in this publication may contain proprietary, 
patented, or copyrighted techniques, components, or materials. Under no circumstances shall any user be 
conveyed any license or right to the use or ownership of such items.

All rights reserved. ©2013 Linx Technologies 

The stylized Linx logo, Wireless Made Simple, CipherLinx and the stylized CL logo are trademarks of Linx Technologies.

Содержание MDEV-900-TT




























Отзывы: