NOTE: DO NOT RETURN
THIS PRODUCT TO THE STORE
(Many problems can be resolved without returning this product to the retailer.)
If you are unhappy or there are technical issues, please call us at: 561-972-8381
®
Monitor and Detect Lint Build-up
in Your Dryer Duct
LintAlert Model ALRT31 Installation Manual
Congratulations – Your In-O-Vate Technologies LintAlert
dryer exhaust monitor is the most advanced, innovative
and effective pressure sensing monitor for the dryer on
the market today. It is designed to provide progressive
notice of airflow blockage in your dryers’ exhaust duct.
Introduction
The U.S. Consumer Product Safety Commission estimates that 15,500 clothes
dryer fires occur in U.S. homes annually, averaging about 10 deaths, 300
injuries and $85 million in direct property damage. Lint build-up and lack of
maintenance is the number one cause of dryer fires. Your LintAlert home
safety device for the clothes dryer can provide a visual indication of how much
additional pressure exists over time due to lint buildup or blockage of some sort
in the duct work between the dryer and the exterior termination vent.
How it Works
The LintAlert monitors and displays the back pressure levels found in the exhaust
conduit of the dryer. Pressure levels found in the duct work between the back of
the dryer and the exterior vent hood typically increase over time due to lint build-
up or other restrictions like birds nest or vent hoods that become inoperable. The
LintAlert incorporates a very innovative and responsive digital low differential air
pressure sensor. Coupled with a smart programmable integrated microprocessor,
the device can determine if your dryer is running, and what levels of pressure
exist. When the pressure level reaches a point that is unsafe the “alarm state”
will indicate its time to clean out the duct work. Prior to the alarm state, a slow
progression of the LED light bar will indicate fractional build-up.
Before You Begin (Items in Package)
Please review the parts and make sure they are present. Refer to the Installing
the LintAlert section for proper installation.
1. Alert Module: the plug-in component that contains the electronics and air
pressure sensor (120V 60Hz 15 AMPS max pass through).
2. Tap Fitting: four pieces (2a. umbrella shaped tap fitting, 2b. felt washer, 2c.
curved washer and 2d. nylon thumb nut).
3. Tubing: approximately 6 feet of 1/8” inside diameter by ¼” outside diameter clear
vinyl PVC.
NOTICE: Please Read This Prior to Calibrating the LintAlert:
In order for the LintAlert to accurately monitor the air
pressure levels in your specific dryer duct system and warn
of any unsafe levels, the device needs to be calibrated to your
particular system at a LIKE NEW or VERY CLEAN STATE.
In technical terms, the clean pressure value must be recorded to memory in order to
provide an accurate scale of build-up intervals. The LintAlert will not initialize or may
not initialize correctly if the dryers’ exhaust condition is not in a like new clean state.
This like new state can be achieved by hiring a professional duct cleaner or doing it
yourself with a dryer vent cleaning kit. These kits are readily available online or at
hardware stores and are comprised of a rotating action auger brush and flexible rods.
Technical Support Options:
Online: Extensive FAQ’s Available – www.lintalert.com
Phone: 561-972-8381
Email: [email protected]
Hours: 7 am to 11 pm EST, 7 Days a Week
Manufactured by:
In-O-Vate Technologies, Inc.
810 Saturn Street, Suite 21 Jupiter, FL 33477
US Patent 6,785,981, Others Pending Copyright ©2010 In-O-Vate
Technologies, Inc. All rights reserved. LintAlert is a registered trademark of
In-O-Vate Technologies, Inc. Proudly made in the U.S.
Registration
Congratulations on your purchase of the LintAlert®. To fully
benefit from the support that In-O-Vate Technologies offers,
please register your product at www.lintalert.com/register.htm.
Limited Warranty and Service
In-O-Vate Technologies warrants to the original purchaser that the enclosed dryer
exhaust monitoring system will be free from defects in materials, workmanship or
design under normal use and service for a period of one year from the date of
purchase provided that it is properly used as prescribed by the owner’s guide.
The obligation of In-O-Vate Technologies under this warranty is limited to, at our
option, repairing or replacing the LintAlert or any part which we find to be defective
in material, workmanship or design, free of charge to the customer provided that
prior to any return, a Return Authorization (RA) number and shipping instructions
are attained by contacting In-O-Vate Technologies Customer Service.
This warranty shall be void if registration is not completed and sent to In-O-Vate
Technologies, Inc. customer services within 30 days of purchase. This warranty
shall not apply to the LintAlert system if it has been damaged, modified, abused
or altered after the date of purchase or if it fails to operate due to improper
maintenance or problems caused by inadequate A.C. electrical power or power
fluctuations.
THE LIABILITY OF IN-O-VATE TECHNOLOGIES OR ANY OF ITS PARENT
OR SUBSIDIARY CORPORATIONS ARISING FROM THE SALE OF THIS
DRYER EXHAUST MONITORING DEVICE OR UNDER THE TERMS OF THIS
LIMITED WARRANTY SHALL NOT IN ANY CASE EXCEED THE COST OF
REPLACEMENT OF THE LINTALERT MONITORING DEVICE AND, IN NO
CASE, SHALL IN-O-VATE TECHNOLOGIES OR ANY OF ITS PARENT OR
SUBSIDIARY CORPORATIONS BE LIABLE FOR CONSEQUENTIAL LOSS
OR DAMAGES RESULTING FROM THE FAILURE OF THE LINTALERT
MONITORING DEVICE OR FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS
CAUSED BY THE COMPANY’S NEGLIGENCE OR FAULT. While this warranty
gives you specific rights, you may also have other rights which vary from state to
state. Since some states do not allow limitations on the duration of an implied
warranty or do not allow the exclusion or limitation of incidental or consequential
damages, the above limitations or exclusions may not apply to you.
If, after reviewing this manual, you feel that your LintAlert dryer exhaust
monitoring device is defective in any way, do not tamper with the unit or return it
to the store you bought it at. Obtain customer or technical service in the U.S. or
Canada, by calling In-O-Vate Technologies at 561-972-8381. THIS IS IN-O-VATE
TECHNOLOGIES COMPLETE WARRANTY FOR THE PRODUCTS. The above
warranty may not be altered except in writing by In-O-Vate Technologies.
2a
2b
2c
2d
3
1
