106
2. I’m having problems connecting to the Internet, what LEDs should be
lit on the front of the Router?
•
Each Router’s LED will light up for any proper connection made on the back
of the Router—whether it is an Ethernet cable or power cord.
For example, the following are typical LEDs that light up once a computer and
DSL modem are connected:
-
When the Router is turned on (the power adapter is plugged into the
Router), the
Power
LED lights up.
-
When an Ethernet cable is properly connected between a PC and Port 4
of the Router, the
Link/Act
,
Ful/Col
, and
100
LEDs in Column 4 light up.
-
ADSL modem connection causes the
WAN Link
LED to light up.
Dynamic IP
Address (DHCP)
1. Select
Obtain an IP automatically
as the WAN
Connection Type.
2. Click the
Apply
button to save the setting.
Perform these steps:
PPPoE
1. Select
PPPoE
as the WAN Connection Type.
2. Enter the
User Name
.
3. Enter the
Password
.
4. Click the
Apply
button to save the settings.
5. Click on the Status tab then on the Connect button to
launch the connection.
Static IP Address
1. Select
Static IP
as the WAN Connection Type.
2. Enter the
IP Address
.
3. Enter the
Subnet Mask
.
4. Enter the
Gateway Address
.
5. Enter the
DNS
in the 1, 2, and/or 3 fields.
You need to enter at least one DNS address.
6. Click the
Apply
button to save the settings.
RAS or PPTP
If you are using RAS (Singapore SingTel) or PPTP
(service in Europe), check with your ISP for the
necessary setup information.
If you have this type
of connection:
107
•
My
WAN Link
LED isn’t lit. What should I check?
-
Check that the cable you are using between your ADSL modem
and the Router is the same cable that came with your modem.
Depending on the type of connection your modem uses, you may
need either a
“straight-through” or “crossover” Ethernet cable (the “straight-through”
type is more common).
•
Some of the lights on the front of the Router don’t light up when I plug in a PC.
- Only
the
Link/Act
LED is required for a connection to work correctly.
3. I cannot get onto the Internet, nor can I access the Router’s Setup page.
What should I check?
A. First check that the ADSL modem and computers are properly connected to
the Router. See Question #2 for how to verify that the connections are good.
B. Then, check that you have properly configured your PCs to communicate with
the Router. Below you will find instructions for the various versions of
Windows.
-
Windows 98 SE, or ME
•
Click the
Start
menu, and then click
Run
. After the Run window
appears, enter
winipcfg
in the Open field, and then click the
OK
button.
•
When the IP Configuration window appears, click the
gray box
with
a black arrow pointing down.
•
A list of adapters will appear. Select the
adapter
that you use to connect
to the Internet. These items should not contain “PPP”, “VPN”, “AOL”, or
“Dial-Up adapter” as part of the entry.
•
The IP Address field should show an IP address of 192.168.1.100 or
192.168.1.xxx, with “xxx” being any number greater than 100.
If your IP address is not in that range, hold the reset button on the front
of the Router for more than 30 seconds. This will cause your Router to
be set to factory default, so you will need to re-configure the Router's
Setup page. After re-configuring the Setup page, restart the computer.
-
Windows NT, 2000, and XP
•
Click the
Start
menu, and then click
Run
. After the Run window
appears, enter
cmd
in the Open field, and then click the
OK
button.
•
This will open a command prompt. Enter
ipconfig /all
and then press
the
Enter
key.
Instant Wireless™ Series
Wireless Access Point Router with 4-Port Switch
Содержание BEFW11S4 ver.3
Страница 60: ...118 119 ...
Страница 61: ... Copyright 2003 Linksys All Rights Reserved www linksys com ...
