LINK LABS LL-RLP-20 Скачать руководство пользователя страница 12

 

 

LL-RLP-20 Datasheet 

www.link-labs.com

    

Information contained in this document is subject to change without notification

 

 

10 

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT 

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates 
uses and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct the interference by one of the 
following measures: 
 

 

Reorient or relocate the receiving antenna.  

 

Increase the separation between the equipment and receiver.  

 

Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected.  

 

Consult the dealer or an experienced radio/TV technician for help. 

 

 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation.  

 

FCC CAUTION: Any changes or modifications not expressly approved by the party 

responsible for compliance could void the user's authority to operate this equipment.

 

 

Conformité aux normes FCC Cet équipement a été testé et trouvé conforme aux limites pour un 
dispositif numérique de classe B, conformément à la Partie 15 des règlements de la FCC. Ces 
limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles 
dans une installation résidentielle. 
 
Cet équipement génère, utilise et peut émettre des fréquences radio et, s'il n'est pas installé et 
utilisé conformément ment aux instructions du fabricant, peut causer des interferences nuisibles 
aux communications radio. 
 
Rien ne garantit cependant que l'interférence ne se produira pas dans une installation 
particulière. Si cet équipement provoque des interférences nuisibles à la réception radio ou de 
télévision, qui peut être déterminé en comparant et en

l'éteignant, l'utilisateur est encouragé à 

essayer de corriger les interférence par une ou plusieurs des mesures suivantes: 
 

 

Réorienter ou déplacer l'antenne de réception.

 

 

Augmenter la distance entre l'équipement et le récepteur.

 

 

Branchez l'appareil dans une prise sur un circuit différent de celui auquel le récepteur 
est connecté.

 

 

Consultez votre revendeur ou un technicien radio / TV pour assistance.Avertissement 

 
 

Содержание LL-RLP-20

















Отзывы: