manualshive.com logo in svg

Link Controls CDO Series, Инструкция по эксплуатации, Страница: 3 / 12

Поделиться
Скачать
Link Controls CDO Series Скачать руководство пользователя страница 3

 Door Operator / CDO / LC- 3158 Rev.B  – 3 

Regulations and bases for testing

For connecting, programming and servicing, the following 
regulations must be observed (the list is not exhaustive).

Construction product standards

-  EN 13241-1 (Products without fire resistance or smoke 

control characteristics)

-  EN 12445 (Safety in use of power operated doors -  

Test methods)

-  EN 12453 (Safety in use of power operated doors -  

Requirements)

-  EN 12635 (Industrial, commercial and garage doors and 

gates - Installation and use.)

-  EN 12978 (Safety devices for power operated doors and 

gates - Requirements and test methods)

Electromagnetic compatibility
-  EN 55014-1 (Radio disturbance, household  appliances)
-  EN 61000-3-2 (Disturbances in supply systems -  

harmonic currents)

-  EN 61000-3-3 (Disturbances in supply systems -  

voltage fluctuations)

-  EN 61000-6-2 (Electromagnetic compatibility (EMC) -  

Part 6-2: Generic standards - Immunity for industrial 
 environments)

-  EN 61000-6-3 (Electromagnetic compatibility (EMC) -  

Part 6-3: Generic standards - Emission standard for 
 residential, commercial and light- industrial environments)

Machinery guidelines
-  EN 60204-1 (Safety of machinery,  electrical  equipment of 

machines, part 1: general  requirements)

-  EN 12100-1 (Safety of machinery. Basic concepts, 

general principles for design. Basic terminology, 
methodology)

Low voltage
-  EN 60335-1 (Household and similar electrical 

appliances - Safety)

-  EN 60335-2-103 (Particular requirements for drives for 

gates, doors and windows)

Various options

The following package options are available for the 

flange mounted CDO Rolling Door operator:

The operators listed below can be supplied with 
various manual overrides.

CDO-50 1ph

CDO-100 3ph / 1ph

CDO-150 3ph

CDO-175 3ph

CDO-200 3ph / 1ph

CDO-275 3ph

CDO-300 3ph

CDO-375 3ph

CDO-400 3ph

4.   Overview of products

Содержание CDO Series













Отзывы:

Нет отзывов