Linear DXS-80 Скачать руководство пользователя страница 4

  

SECTION 

LINEAR LLC 

FCC ID:  EF4 SST00116

 

 

LABEL FACSIMILE 

 

 
Linear Corp. requests authority to use the label as depicted, in accord with Section 
2.925(e) of the Commission's Rules, follows herein. 
 
 
 
FCC ID: EF4 SST00116 
Linear LLC 
Model:  DXS-80, CO Alarm 
Frequency: 315 MHz 

 

Request for Authorization of Section 2.925(e) 
 
The device for which Linear seeks authority is small in size and has other safety related 
mandatory UL text.  The small size of the product and minimum text size of the UL 
warnings and cautions does not lend itself to the placement of a label in accord with the 
FCC and IC labeling requirements. 
 
Accordingly, Linear requests authority to place upon the device an identification label 
such as the one depicted herein identified as LABEL FACSIMILE. 
 
The additional information which is normally required to be included with the FCC 
Identification Number in accord with Part 15 of the Commission's Rules shall be located 
herein as a portion of the draft manual attached hereto. 
 
Accordingly, in accord with Section 2.925(e) of the Commission's Rules and past 
Commission decisions, Linear hereby requests authority to label its devices in the 
manner described herein. 
 
The user instruction manual will have the full text of the FCC disclaimer printed in a 
prominent location at the end of the installation instructions as follows: 

  

This device complies with FCC Part 15 and Industry Canada Rules and Regulations.  Operation 
is subject to the following two conditions: (1) This device may not cause harmful interference, and 
(2) This device must accept any interference received , including interference that may cause 
undesired operation. 

 

Содержание DXS-80












































Отзывы: