Black
0002
Black
0002
CONTENTS
INTRODUCTION
Linear’s AccessKey is a digital keyless entry system
designed for access control applications. The keypad is
housed in a rugged cast aluminum enclosure that can be
mounted to a pedestal or bolted directly to a wall. The
die-cast keys have bright, easy-to-read yellow graphics.
Up to 480 entry codes, from 1 to 6 digits in length, can be
programmed. They can activate either, or both, of the relay
outputs. Relay #1 has a 5 Amp capacity. Relay #2 has a
1 Amp capacity.
Two LED indicators show the status of the entry system.
The left LED lights red to indicate power, then turns green
when access is granted. The right LED lights yellow when
the keypad is in “lockout” condition (from too many
incorrect code entries). The keypad’s courtesy light
illuminates the keys for two minutes after any key is pressed.
An internal sounder beeps when each key is pressed.
The DOOR SENSE/INHIBIT input can be used two ways.
If programmed for “door sense”, a switch on the door
detects forced entry or door ajar situations. If programmed
for “inhibit”, the input can be wired to a “service” switch or
automatic timer that will disable the Relay #1 when
required.
The REQUEST-TO-ENTER input can be wired to a
pushbutton or fire access keyswitch to provide codeless
entry for authorized personnel. The “anti-passback”
feature prevents using the same code twice before the
programmed time elapses.
The ALARM SHUNT output activates when access is
granted. This output can be wired to shunt alarm contacts
on the access door/gate to prevent triggering of an alarm
when authorized access occurs.
Two solid state outputs, capable of switching 100 mA to
common, are programmable to signal forced entry, door
ajar, lockout, alarm circuit shunting, request-to-enter, and
keypad active conditions.
The AccessKey is powered from a 12-24 Volt AC or DC
source. Power can be obtained from the access device or
a separate power supply. The EEPROM memory retains
all entry codes and programming, even without power.
SPECIFICATIONS
MECHANICAL
Case dimensions: 4.00" W x 5.50" H x 3.00" D
ELECTRICAL
Voltage: 12-24 Volts AC or DC
Current: 10 mA typical, 150 mA maximum
Outputs: Relay #1
Form “C” 5 Amps @ 24 Volts maximum
Relay #2
Form “C” 1 Amp @ 24 Volts maximum
Solid state outputs (Outputs #3 & #4)
Short-to-common 100 mA
@ 24 VDC maximum
ENVIRONMENTAL
Temperature: -22°F to 149°F (-30°C to 65°C)
Humidity: 5% to 95% non-condensing
FEATURES
KEYPAD PROGRAMMABLE
480 ENTRY CODE CAPACITY
1-6 DIGIT ENTRY CODE LENGTH
4 INDEPENDENT OUTPUTS (TIMED/TOGGLED)
4 INDEPENDENT TIMERS
EACH ENTRY CODE CAN BE PROGRAMMED TO ACTIVATE EITHER OR
BOTH RELAYS
RELAY CONTACTS ARE FORM “C” (N.O. & N.C)
SOLID STATE OUTPUTS ARE OPEN COLLECTOR (SWITCH-TO-COMMON)
TWO LED INDICATORS
COURTESY LAMP
PIEZO SOUNDER
TIMED ANTI-PASSBACK (LAST 3 VALID ENTRIES)
KEYPAD LOCKOUT
TACTILE KEY FEEL
DOOR SENSE INPUT
INHIBIT INPUT
REQUEST-TO-ENTER INPUT
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
COMPONENT LOCATIONS . . . . . . . . . . . . . . . . . . . . . . 3
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
FACTORY DEFAULTS . . . . . . . . . . . . . . . . . . . . . . . . . 6
BASIC PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . 6
PROGRAMMING OPTIONS . . . . . . . . . . . . . . . . . . . . . 7
ACCESSKEY OPERATION . . . . . . . . . . . . . . . . . . . . . . 10
MANAGER’S ENTRY CODE LOG . . . . . . . . . . . . . . . . . . 11
LINEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . 12
FCC NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2