Linear Tube Audio Z10 Seriers Скачать руководство пользователя страница 8

Center  Button

:  This  normally  functions  as  a  Mute  function.  When 

the unit is muted, there are two Xs on the display.   When in Menu 

Mode, the Center button functions as a Select button.   

Menu Button

: When in normal operation, selects the Menu Mode. 

In the menu, this functions as a Select button. 

Play/Pause Button

: This is only used to pair a new Apple remote to 

the unit, which is done by holding the button down for 30 seconds. 

Menu 

The menu is accessed via the Menu button on the remote control. 

Scroll  with  the  up  and  down  buttons  to  see  menu  options.  Pause 

on an option to see the entire title scroll by. 

Balance: 

Use  the  right  and  left  remote  buttons  to  adjust  the 

balance.  The  front  panel  displays  the  balance  setting  as  you 

adjust  -  two  bars  in  the  center  indicate  that  the  balance  is  at  0 

(both  channels  are  equal).  When  the  desired  balance  level  is 

selected,  press  the  center  button  to  save  the  setting.  A  message 

will  appear  on  the  display  to  indicate  which  setting  the  balance 

has been set to. The balance setting is saved across all inputs and 

will  be  utilized  upon  power  up  to  the  last  saved  setting.    The 

maximum balance setting is 16 levels difference. 

Brightness:

  The  front  panel  display  can  be  set  to  16  levels  of 

brightness.  The  brightness  levels  are  saved  and  recalled  upon 

power on. 

Display Timeout:

  The volume display and input LEDs can be set to 

turn  off  after  10  seconds.  They  will  reappear  if  a  button  on  the 

remote control is pressed or the volume knob or front panel switch 

is changed.  There are 3 settings: 

OFF - The volume display and input LEDs remain on. 

VOL - The volume display turns off but the input LEDs remain on. 

ALL - The volume display and input LEDs turn off. 

Содержание Z10 Seriers













Отзывы: