background image

1

dc1540bf

DEMO MANUAL DC1540B

DESCRIPTION

LTC2977 8-Channel 

Power System Manager 

with EEPROM

The DC1540B is a demonstration system for the 

LTC

®

2977

 

8-channel I

2

C/SMBus/PMBus Power System Manager 

with EEPROM. It consists of 2 circuit boards namely the 

DC1360B and DC1361B. The DC1360B contains all the 

circuitry needed to insert the LTC2977 into a power system 

and control eight power supplies. The DC1361B contains 

eight power supplies (LTM4603EV) which are configured 

to be controlled by an LTC2977. Together these two boards 

form a sophisticated, 8-channel, digitally programmable 

power supply.
This demonstration system is supported by LTpowerPlay™ 

software and a graphical user interface (GUI) that enables 

complete control of all the LTC2977 features. You can obtain 

this GUI from the website www.linear.com/ltpowerplay.

com. LTpowerPlay and the DC1540B, create a powerful 

development environment in which you can design config-

uration settings for the LTC2977. The configuration settings 

can be stored in the LTC2977 EEPROM and also in a file, 

which can be used to order pre-programmed devices.  

LTpowerPlay displays all of the configuration settings and 

real-time measurements that the LTC2977 performs and 

allows easy access to the fault log created by the LTC2977. 

The LTC2977 on the DC1360B comes pre-programmed with 

EEPROM values appropriate for the eight power supplies 

used on the DC1361B. 
The LTC2977 can be configured to monitor current 

on odd numbered channels. In the DC1540B, this 

feature can be enabled on Channel 7 (see “Measur-

ing Current”). Channels 1 and 2 can be configured 

to do coincident tracking of Channel 0 by using JP2 

and JP3 (see “DC1361B Details – Top Side”). An LTC  

Hot Swap™ circuit on the DC1361B enables the LTC2977 to 

soft-start V

IN

 and shut off V

IN

 in response to output faults. 

Multiple DC1540Bs can be cascaded together to form 

a high channel count power supply (see “Multi-Board 

Arrays”). This configuration demonstrates features of the 

LTC2977 which allow timing and fault information to be 

L

, LT, LTC, LTM, Linear Technology, and the Linear logo are registered trademarks and 

LTpowerPlay and Hot Swap are trademarks of Linear Technology Corporation. All other 

trademarks are the property of their respective owners.

shared across multiple LTC2977s, allowing the formation 

of a single, coherent power supply control system. This 

configuration is easily supported by the LTpowerPlay 

GUI and allows the user to configure up to 9 LTC2977s, 

controlling up to 72 separate power supplies. 
To get this demo system up and running, connect the 

DC1540B to your computer using a DC1427A or a DC1613 

(USB to I

2

C/SMBus/PMBus Controller). The following is 

a checklist of items which you can obtain from the LTC 

website or LTC Field Sales.

 n

  USB to I

2

C/SMBus/PMBus Controller (DC1613A)

 n

  LTpowerPlay GUI

 n

  LTC2977 Resistor Selection Tool for calculating    

  resistors values and proper DAC range settings  

  (in the GUI)

 

LTC2977 Features

• I

2

C/SMBus Communication

•  Configuration EEPROM

•  PMBus Compliant

•  Fault Logging to Internal EEPROM

•  Differential Input, 16-bit 

∆S

 ADC with less than ±0.25% 

of Total Unadjusted Error Using On-Chip Reference

•  Monitors Eight Output Channels and One Input Voltage

•  Programmable Watchdog Timer

•  8-Channel Sequencer

•  Eight 10-Bit OV/UV Supervisors 

•  Eight 10-Bit Margin/Trim DAC’s with Soft-Connect

•  A Closed-Loop Digital Servo Accurately Trims the Outputs

•  Supports Multi-Channel Fault Management

•  Programmable Fault Responses

•  On-Chip Digital Temperature Sensor

Design files for this circuit board are available at  

http://www.linear.com/demo

Содержание DC1613A





































Отзывы: