background image

wires, use the alternate methods "B" or "C". 
B. The 

XO-1©

 red wire can be connected along with the amplifier remote turn-on 

(trigger) wire to a CS-1 current sense adaptor (available as an accessory through 
an authorized LINEAR POWER dealer). 
C. The 

XO-1©

 red wire can be connected through a toggle switch (current rating 

is not important) to the fuse panel. 

IMPORTANT:

 THE 

XO-1©

 POWER WIRE 

SHOULD NOT BE DIRECTLY CONNECTED TO A SOURCE OF POWER 
WHICH WILL BE HOT EVEN WHEN THE IGNITION IS TURNED OFF, AS 
BATTERY DRAIN MAY OCCUR AFTER AN EXTENDED PERIOD. 

MAIN GROUND

 

Connect the black ground wire to a car chassis ground, preferably to the same 
point at which the amplifiers are grounded. 

2. 

INPUT

 

Connect the right and left inputs on the 

XO-1©

 to the right and left outputs from 

the music source. If the output of the music source is high level (designed to 
connect directly to a speaker) obtain a set of high level adaptor plugs from your 
LINEAR POWER dealer and follow the enclosed directions. 

3. 

OUTPUTS 

(BI-AMP)

 

Low Frequency: 

 

Connect the right and left low frequency outputs from the 

XO-1©

 to the right and 

left inputs on the low frequency amplifier. The low frequency speakers (woofers) 
can then be connected to the output of the low frequency amplifier. 

High Frequency: 

 

Connect the right and left high frequency outputs from the 

XO-1©

 to the right and 

left inputs on the high frequency amplifier. (See DIAGRAM A for 
interconnections.) 

 

4. 

OUTPUTS  

(Mono-bridge subwoofer)

 

 

In a mono subwoofer system, the low frequency amplifier's outputs are strapped 
together (bridged) by the 

XO-1©

 to sum the power of both channels into one to 

drive a single 8 ohm woofer. In this configuration, both of the speaker ground 
wires are unused and should be taped and dressed away from the other wiring. 
The woofer can then be connected directly across the right and left speaker 
output "hot" wires from the low frequency amplifier by attaching the green wire to 
the woofer positive terminal and the grey wire to the negative terminal. 

© 2008 Linear Power, Inc. - ALL RIGHTS RESERVED 

LINEAR POWER™ is a trademark of Linear Power, Inc.

 

 

3

Содержание EQ-1








Отзывы: