manualshive.com logo in svg

Lincoln LN-25 PRO, Руководство оператора

Поделиться
Скачать
Lincoln LN-25 PRO Скачать руководство пользователя страница 33

D-2

MAINTENANCE

D-2

WIRE FEED SPEED VALIDATION

Calibration  of  the  LN-25™  PRO  may  be  required  when
the  P.C.  board,  wire  feed  speed  potentiometer  or  motor
is replaced or serviced.  Calibration matches the scale on
the name plate to the actual wire feed speed.

To calibrate the LN-25™ PRO:

1. Turn power OFF at the welding source.

2. Remove  the  spool  of  wire  and  the  cover  from  the

feeder. Remove the gun from the feeder plate, leav-
ing  the  gun  trigger  attached  to  the  feeder.  Remove
the  plastic  cover  on  the  feed  plate  to  reveal  the
motor gear.

3. Place the WFS range switch in the “high” setting. Set

the WFS knob to

• 50 ipm for K2613-5
• 25 ipm for K2613-7

4. Trigger  the    LN-25™  PRO  and  measure  the  rpm  of

the  motor  gear.  Adjust  the  WFS  knob  as  required
until the rpm measures 8.9 to 9.2 rpm.

5. Insert  the  shorting  plug  into  the  control  board  for  1

second  and  then  remove  the  shorting  plug.  The
shorting plug shorts pins 4 and 7 of J3.

6. Set the WFS knob to

• 800 ipm for K2613-5
• 400 ipm for K2613-7

7. Trigger  the  LN-25™  PRO  and  measure  the  rpm  of

the  motor  gear.  Adjust  the  WFS  knob  as  required
until the rpm measure 128.0 to 130.0 rpm.

8. Insert  the  shorting  plug  into  the  control  board  for  1

second  and  then  remove  the  shorting  plug.  The
shorting plug shorts pins 4 and 7 of J3.

9. Turn power OFF and reassemble.

LN-25™ PRO

FIGuRE D.2

Содержание LN-25 PRO












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды