Lincoln LN-25 PRO Скачать руководство пользователя страница 10

Страница: 10 / 43

A-1

INSTALLATION

A-1

LN-25™ PRO

TEMPERATuRE RANGE

OPERATION:

-40°F to 104°F (-40°C to 40°C)

STORAGE:

-40°F to 122°F (-40°C to 50°C)

INPuT VOLTAGE and CuRRENT

TEChNICAL SPECIFICATIONS – LN-25™ PRO (K2613-5, K2613-7)

hEIGhT

WIDTh

DEPTh

WEIGhT

14.8 Inches

8.7 Inches

23.2 Inches

38 lbs

(376 mm)

( 221 mm)

(589 mm)

(17 kg)

Handle folded down

PhYSICAL DIMENSIONS

INPuT VOLTAGE ± 10%

15-110 VDC

INPuT AMPERES

RATED OuTPuT @ 104°F (40°C)

DuTY CYCLE

60% rating

INPuT AMPERES

450

GEARING - WIRE FEED SPEED RANGE-WIRE SIzE

WFS RANGE

50 – 400 ipm

(1.3 – 10.1m/min)

50 – 700 ipm

(1.3 – 17.7m/min)

WFS RANGE

50 – 400 ipm

(1.3 – 10.1m/min)

50 – 700 ipm

(1.3 – 17.7m/min)

WIRE SIzES

.023 – 1/16"

(0.6 – 1.6mm)

.023 – 1/16"

(0.6 – 1.6mm)

WIRE SIzES

.030 - 3/32”

(0.8 – 2.4mm)

.030 - 5/64

(0.8 - 2.0mm)

GEARING

Extra torque

K2613-7

Standard Speed

K2613-5

GMAW

FCAW

Thermal tests have been performed at ambient temperature. The duty cycle (duty factor) at 40°C has been deter-
mined by simulation.

Duty cycle is based upon the amount of welding performed in a 10 minute period.

IP23

Содержание LN-25 PRO












































Результаты поиска

Содержание LN-25 PRO

Отзывы:

Бренды по названию

Популярные бренды

Lincoln LN-25 PRO, Руководство оператора

Результаты поиска

Содержание LN-25 PRO

Отзывы:

Бренды по названию

Популярные бренды