Lincoln FlowMaster 85850 Скачать руководство пользователя страница 4

Страница: 4 / 25

Page Number - 4

FlowMaster

Rotary Driven Electric Pump

Form 404059

Illustration 4

A - Safety Unlader 272722

B - 50 Hz, 3 Phase, 380-420 VAC

C - Outlet Shut-off Valve

D - Material Supply Line

E - Follower Plate (85492 for 120 lb. drum only)

F - Drum Cover (85475 for 400 lbs., 85474 for 120 lbs.)

G - Auxillary Motor Mount

ELECTRIC FLOWMASTER PUMP

50 Hz, 380 VAC, 5:1 gear ratio, 85851 & 85850

BACK PRESSURE (PSI) RPM CURRENT DRAW (AMPS) (@ 420 VAC)*

300

1 (.9)

1000

285

1 (.9)

2000

285

1 (.9)

3000

285

1.1 (1.0)

4000

285

1.2 (1.1)

5000

285

1.3 (1.2)

Operation

1. Remove the pump outlet line.

2. With the pump in a full container of lubricant, energize the

pump. Make sure all air has been expelled from the pump

and even lubricant flow is achieved.

3. Reattach the pump outlet line. Never allow the pump to run

dry of lubricant. Monitor the supply lubricant level and refill

when necessary.

Illustration 3

AC motor requires an auxillary mount. Do not operate the

pump without properly mounting the motor to the drum cover.

• Follow local eletric code when choosing and sizing motor

starter.

• Follow local eletric codes when wiring motor.

• Wiring must be done by a qualified electricion.

Crankcase Oil Service Interval Recommendations

• Check the oil level after every 750 hours of machine opera-

tion, or every month.

• Change the oil after every 2,000 hours of machine opera-

tion or every year.

• Use SAE 10W30 motor oil in all units used in an ambient

temperature between 150 to -40°F. For ambient tempera-

tures between 50 to -70°F, use Mobil Arrow HFA Low

Temperature oil.

• Oil level should be at the dot on the dipstick (middle of the

crankshaft) using 10W30 motor oil (15 oz.).

Illustration 2

Содержание FlowMaster 85850


























Результаты поиска

Содержание FlowMaster 85850

Отзывы:

Похожие инструкции для FlowMaster 85850

Бренды по названию

Популярные бренды

Lincoln FlowMaster 85850, Руководство пользователя

Результаты поиска

Содержание FlowMaster 85850

Отзывы:

Похожие инструкции для FlowMaster 85850

Бренды по названию

Популярные бренды