manualshive.com logo in svg

Lincoln Electric VANTAGE 575 CUMMINS, Руководство оператора, Страница: 30 / 54

Поделиться
Скачать
Lincoln Electric VANTAGE 575 CUMMINS Скачать руководство пользователя страница 30

7. Inspect for holes and tears by looking through the element

toward a bright light. Check for damaged gaskets or dented
metal parts. Do not reuse damaged elements. Protect element
from dust and damage during drying and storage.

8. Reinstall air filter element.

After six cleanings replace air filter. A cleaned filter will have
approximately 70% of the life of a new filter element. A restricted
filter element may not appear excessively dirty.

FUEL FILTERS

When working on the fuel system:

• Keep naked lights away !

• Do not spill fuel !

• Do not smoke !

--------------------------------------------------------------------------------------

The Vantage 575 is equipped with a 

Fuel Filter

located after the

lift pump and before fuel injectors.The procedure for changing the
filter is as follows.

1. Close the fuel shutoff valve.

2. Clean the area around the fuel filter head. Remove the filter.

Clean the gasket surface of the filter head and replace the o-
ring.

3. Fill the clean filter with clean fuel, and lubricate the o-ring seal

with clean lubricating oil.

4. Install the filter as specified by the filter manufacturer.

Mechanical overtightening will distort the threads, filter
element seal or filter can.

--------------------------------------------------------------------------------------

COOLING SYSTEM

The Vantage 575 is equipped with a pressure radiator. Keep the
radiator cap tight to prevent loss of coolant. Clean and flush the
coolant system periodically to prevent clogging the passage and
over-heating the engine.

BATTERY HANDLING

GASES FROM BATTERY can explode.

• Keep sparks, flame and cigarettes away from

battery.

To prevent EXPLOSION when:

• INSTALLING A NEW BATTERY - disconnect

negative cable from old battery first and
connect to new battery last.

• CONNECTING  A

BATTERY

CHARGER  -

Remove battery from welder by disconnecting
negative cable first, then positive cable and
battery clamp. When reinstalling, connect
negative cable last. Keep well ventilated.

• USING A BOOSTER - connect positive lead to

battery first then connect negative lead to
engine foot. 

BATTERY ACID CAN BURN EYES AND SKIN.

• Wear gloves and eye protection and be careful
when working near battery. Follow instructions
printed on battery.

--------------------------------------------------------------------------------------

PREVENTING ELECTRICAL DAMAGE

1. When replacing, jumping, or otherwise connecting the battery

to the battery cables, the proper polarity must be observed.
Failure to observe the proper polarity could result in damage to
the charging circuit. The positive (+) battery cable has a red
terminal cover.

2. If the battery requires charging from an external charger,

disconnect the negative battery cable first and then the positive
battery cable before attaching the charger leads. Failure to do
so can result in damage to the internal charger components.
When reconnecting the cables, connect the positive cable first
and the negative cable last.

PREVENTING BATTERY DISCHARGE

Turn the RUN/STOP switch to stop when engine is not running.

PREVENTING BATTERY BUCKLING

Tighten nuts on battery clamp until snug.

D-2

MAINTENANCE

D-2

Vantage 575

WARNING

WARNING

Содержание VANTAGE 575 CUMMINS























































Отзывы:

Нет отзывов