manualshive.com logo in svg

Lincoln Electric Vantage 441X/LE500X, Руководство оператора

Поделиться
Скачать
Lincoln Electric Vantage 441X/LE500X Скачать руководство пользователя страница 43

D-2

MAINTENANCE

ENGINE MAINTENANCE 

Refer to the SERVICE PLAN section of the Engine Operator’s 

Manual for the recommended maintenance schedule of the 

following: 

a) Engine Oil and Filter
b) Air Cleaner
c) Fuel Filter and Delivery System
d) Alternator Belt
e) Battery
f) Cooling System

Refer to Table D.1 at the end of this section for various engine 

maintenance components. 

AIR FILTER 

•

Never run the engine without the air cleaner. Rapid
engine wear will result from contaminants, such as dust
and dirt being drawn into the engine.

The diesel engine is equipped with a dry type air filter. Never 

apply 

oil to it. Service the air cleaner per instructions on page D-3. 

Replace air filter element as needed per the service indicator. 

If no 

indicator is present, clean as needed and replace every 1000

 

hours of operation. Under dusty conditions, replace sooner. 

WARNING

VANTAGE

®

 441X

/LE500X

 

•

Excessive air filter restriction will result in reduced 

engine life.

•

Never use gasoline or low flash point solvents for 

cleaning the air cleaner element. A fire or explosion 

could result.

Содержание Vantage 441X/LE500X


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды