Lincoln Electric Vantage 441X/LE500X Скачать руководство пользователя страница 13

Страница: 13 / 57

A-5

INSTALLATION

BATTERY CONNECTION

Use caution as the electrolyte is a strong acid that can burn
skin and damage eyes.

The Vantage

441X

/LE500X

is shipped with the negative

battery cable disconnected. Make certain that the RUN/STOP/

IDLE switch is in the STOP position. Remove the four screws

from the battery tray using a screwdriver or a 3/8"(10mm)

socket. Attach the negative battery cable to the negative battery

terminal and tighten using a 1/2"(13mm) socket or wrench.
NOTE: This machine is furnished with a wet charged battery; if

unused for several months, the battery may require a booster

charge. Be careful to charge the battery with the correct polarity.

(See Battery in MAINTENANCE section)

GASES FROM BATTERY can

explode.

•

Keep sparks, flame and cigarettes away
from battery.

To prevent EXPLOSION when:
•

INSTALLING A NEW BATTERY — disconnect negative
cable from old battery first and connect to new
battery last.

•

CONNECTING A BATTERY CHARGER — remove
battery from welder by disconnecting negative cable
first, then positive cable and battery clamp. When
reinstalling, connect negative cable last. Keep well
ventilated.

•

USING A BOOSTER — connect positive lead to battery
first then connect negative lead to negative battery lead
at engine foot.

BATTERY ACID can burn eyes and skin.

• Wear gloves and eye protection and be careful

when working near battery.

• Follow instructions printed on battery.

IMPORTANT

: To prevent ELECTRICAL DAMAGE WHEN:

a) Installing new batteries.
b) Using a booster.

Use correct polarity —

Negative Ground.

EXHAUST OUTLET PIPE

Remove cap from DOC pipe protruding from roof.
Using the clamp provided secure the outlet pipe to the outlet tube

with the pipe positioned such that it will direct the exhaust in the

desired direction away from the air intake. Tighten using a

wrench.

SPARK ARRESTOR

Some federal, state or local laws may require that gasoline or

diesel engines be equipped with exhaust spark arrestors when

they are operated in certain locations where unarrested sparks

may present a fire hazard.
The DOC (Diesel Oxidation Catalyst) unit included with this welder

does not qualify as a spark arrestor. When required by local

regulations, a suitable spark arrestor, such as the K2864-1 must

be installed and properly maintained.

An incorrect spark arrestor may lead to damage to the
engine or adversely affect performance.

SERVICE INDICATOR

Air cleaner service indicator provides a Go/No-Go visual indication

of useful filter service life.

FIGURE A.2

CAUTION

WARNING

EXHAUST OUTLET

CLAMP

VANTAGE

441X

/LE500X

Содержание Vantage 441X/LE500X


























































Результаты поиска

Содержание Vantage 441X/LE500X

Отзывы:

Бренды по названию

Популярные бренды

Lincoln Electric Vantage 441X/LE500X, Руководство оператора

Результаты поиска

Содержание Vantage 441X/LE500X

Отзывы:

Бренды по названию

Популярные бренды