Lincoln Electric RED-D-ARC ES 275I Скачать руководство пользователя | Manualshive

Страница: 23 / 32

background image

ES 275i

E-6

TROubLEShOOTING

E-6

Observe all Safety Guidelines detailed throughout this manual

OuTPuT PRObLEMS

PRObLEMS

(SYMPTOMS)

POSSIbLE

CAuSE

RECOMMENDED

COuRSE OF ACTION

The machine will not produce more
than 200 amps.

1. This may be normal operation. If

the  output  current  exceeds  300
amps,  an  electronic  protection
circuit  will  reduce  the  current  to
less than 200 amps. The machine
will  continue  to  produce  this  low
current until the  protection circuit
is  reset.  Reset  occurs  when  the
output load is removed.

2. Check the input voltage and input

voltage reconnect procedures.
See

Input Voltage Reconnect

Procedure.

3. Check for loose or faulty welding

cables.

If  all  recommended  possible  areas  of
misadjustment  have    been  checked
and  the  problem  persists,

Contact

your local Authorized Field Service
Facility.

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, con-
tact your local authorized field service facility for technical troubleshooting assistance before you proceed.

CAuTION

«
...
21
22
23
24
25
...
»

Содержание RED-D-ARC ES 275I

































Отзывы:

Нет отзывов

Похожие инструкции для RED-D-ARC ES 275I

Бренд: Panasonic Страницы: 132

Бренд: Panasonic Страницы: 10

Бренд: AARU ENGINEERS Страницы: 4

Бренд: JBL Страницы: 28

Бренд: JBL Страницы: 16

Authentics L 16

Бренд: JBL Страницы: 17

Бренд: Keller Страницы: 17

Бренд: Neptune Страницы: 35

Бренд: Peavey Страницы: 4

Бренд: Phoenix Страницы: 27

Бренд: Dynacord Страницы: 2

Бренд: Novetec Страницы: 7

Sentronic 2310-ME

Бренд: LCN Страницы: 2

Бренд: Lampert Страницы: 24

Бренд: gala gar Страницы: 42

Бренд: Sylvania Страницы: 26

STRATA_HEAT 120V

Бренд: LATICRETE Страницы: 12

Vingtor Stentofon SPA-AC6

Бренд: Zenitel Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды