Lincoln Electric RED-D-ARC ES 275I страница 15 Скачать руководство пользователя | Manualshive

Страница: 15 / 32

background image

D-1

MAINTENANCE

D-1

INPuT FILTER CAPACITOR

DISChARGE PROCEDuRE

1. Turn off input power or disconnect input power

lines.

2. Remove the 5/16" hex head screws from the side

and top of the machine and remove wrap-around
machine cover.

3. Be careful not to make contact with the capacitor

terminals that are located in the top and bottom of
the Power Board.

4. Obtain a high resistance and high wattage resistor

(25-1000 ohms and 25 watts minimum). This resis-
tor is not supplied with machine. NEVER USE A
SHORTING STRAP FOR THIS PROCEDURE.

5. Locate the four capacitor terminals (large hex head

cap screws) shown in Figure D.1. One pair at the
top and one pair at the bottom of the Power Board.

6. Use electrically insulated gloves and insulated pli-

ers. Hold body of the resistor and connect resistor
leads across the two capacitor terminals. Hold
resistor in place for 10 seconds. DO NOT TOUCH
CAPACITOR TERMINALS WITH YOUR BARE
HANDS.

7. Repeat discharge procedure for the capacitor on

other two terminals.

8. Check voltage across terminals of all capacitors

with a DC voltmeter. Polarity of capacitor terminals
is marked on PC board above terminals. Voltage
should be zero. If any voltage remains, repeat this
capacitor discharge procedure.

ES 275i

ELECTRIC ShOCK

can kill.

• Have an electrician install and service

this equipment.

• Turn the input power off at the fuse

box before working on equipment.

• Do not touch electrically hot parts.
• Prior to Performing preventative main-

tenance, perform the following capaci-
tor discharge procedure to avoid elec-
tric shock.

---------------------------------------------------------------------

WARNING

UPPER
CAPACITOR TERMINALS

LOWER
CAPACITOR
TERMINALS

INSULATED
GLOVES

INSULATED
PLIERS

POWER
RESISTOR

POWER
BOARD

RIGHT SIDE OF MACHINE

UPPER

CAPACITOR TERMINALS

LOWER

CAPACITOR

TERMINALS

INSULATED

GLOVES

INSULATED

PLIERS

POWER

RESISTOR

POWER

BOARD

RIGHT SIDE OF MACHINE

FIGuRE D.1 — LOCATION OF INPuT FILTER CAPACITOR TERMINALS.

«
...
13
14
15
16
17
...
»

Содержание RED-D-ARC ES 275I

































Отзывы:

Нет отзывов

Похожие инструкции для RED-D-ARC ES 275I

Бренд: Harman Kardon Страницы: 2

MaestroKitchen 100

Бренд: Harman Kardon Страницы: 36

Бренд: jablotron Страницы: 30

Бренд: Teac Страницы: 3

Бренд: Jasic Страницы: 18

Liberty Vertical Picket

Бренд: National ramp Страницы: 9

STExB2X05-S Series

Бренд: E2S Страницы: 20

Бренд: Panasonic Страницы: 16

Бренд: biodex Страницы: 20

Бренд: RED SHIELD Страницы: 25

Caregiver CAS-FAM

Бренд: Secure Страницы: 3

Бренд: Icare Страницы: 27

HTVZD*1C series

Бренд: Halsey Taylor Страницы: 7

Бренд: Soundtrack USA Страницы: 8

Universal XL HD Lifter

Бренд: Garage Smart Страницы: 21

Бренд: Harman Kardon Страницы: 16

Бренд: Kemppi Страницы: 51

Бренд: EAW Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды