Lincoln Electric Power MIG 350MP Скачать руководство пользователя страница 14

Страница: 14 / 47

B-1

OPERATION

COMMON WELDING ABBREVIA-
TIONS

WFS

• Wire Feed Speed

•

Constant Current

•

Constant Voltage

GMAW (MIG)

• Gas Metal Arc welding

GMAW-P (MIG)

•

Gas Metal Arc welding-(Pulse)

GMAW-PP (MIG)

• Gas Metal Arc welding-(Pulse-on-Pulse)

GTAW (TIG)

•

Gas Tungsten Arc welding

SMAW (STICK)

•

Shielded Metal Arc welding

FCAW (INNERSHIELD)

•

Flux Core Arc Welding

POWER MIG

350MP

Read entire Operation section before
operating the POWER MIG

350MP.

ELECTRIC SHOCK can kill.

• Do not touch electrically live

parts or electrode with skin or
wet clothing. Insulate yourself
from work and ground.

• Always wear dry insulating

gloves.

FUMES AND GASES can be
dangerous.

• Keep your head out of fumes.

• Use ventilation or exhaust to

remove fumes from breathing
zone.

WELDING SPARKS can
cause fire or explosion.

• Keep flammable material away.

• Do not weld on closed contain-

ers.

ARC RAYS can burn eyes
and skin.

• Wear eye, ear and body protec-

tion.

Observe all safety information throughout
this manual.

DEFINITIONS OF WELDING MODES

NON-SYNERGIC WELDING

MODES

•

Non-synergic

welding mode requires all welding

process variables to be set by the operator.

SYNERGIC WELDING

MODES

•

Synergic

welding mode offers the simplicity of

single knob control. The machine will select the cor-
rect voltage and amperage based on the wire feed
speed (WFS) set by the operator.

WARNING

Содержание Power MIG 350MP
















































Результаты поиска

Содержание Power MIG 350MP

Отзывы:

Бренды по названию

Популярные бренды

Lincoln Electric Power MIG 350MP, Руководство оператора

Результаты поиска

Содержание Power MIG 350MP

Отзывы:

Бренды по названию

Популярные бренды