Lincoln Electric Power MIG 350MP Скачать руководство пользователя страница 12

Страница: 12 / 47

A-5

INSTALLATION

DO NOT ATTACH THE REGULATOR IF OIL,
GREASE OR DAMAGE IS PRESENT!

Inform your

gas supplier of this condition. Oil or grease in the
presence of high pressure oxygen is explosive.

3. Stand to one side away from the outlet and open

the cylinder valve for an instant. This blows away
any dust or dirt which may have accumulated in the
valve outlet.

Be sure to keep your face away from the valve
outlet when “cracking” the valve.

4. Attach the flow regulator to the cylinder valve and

tighten the union nut(s) securely with a wrench.

NOTE:

If connecting to 100% CO

cylinder, insert

regulator adapter between regulator and cylinder
valve. If adapter is equipped with a plastic washer,
be sure it is seated for connection to the CO

cylin-

der.

5. Attach one end of the inlet gas hose to the outlet

fitting of the flow regulator, the other end to the
POWER MIG

350MP rear fitting, and tighten the

union nuts securely with a wrench.

6. Before opening the cylinder valve, turn the regula-

tor adjusting knob counterclockwise until the
adjusting spring pressure is released.

7. Standing to one side, open the cylinder valve slow-

ly a fraction of a turn. When the cylinder pressure
gauge pointer stops moving, open the valve fully.

Never stand directly in front of or behind the flow
regulator when opening the cylinder valve. Always
stand to one side.

-----------------------------------------------------------

8. The flow regulator is adjustable. Adjust it to the flow

rate recommended for the procedure and process
being used before making the weld.

INSTALLING TIG TORCH

The POWER MIG

350MP is programmed to allow it

to be used as a DC TIG welder. The following infor-
mation addresses the installation of an air-cooled TIG
torch with separate power cable and a separate gas
hose (2-cable style).

Connecting TIG Torch:

(See Figure A.4)

ELECTRIC SHOCK can kill.

Turn off welder before adding or
installing accessory items.

-----------------------------------------------------------

1. Tightly secure work lead to positive stud (+).

2. Tightly connect the Power cable to Negative stud (-).

3. Connect the gas supply line to the connector on the

front of the machine.

4. After following the previous instructions of installing

the cylinder and regulator, locate gas connection on
the back of the machine which is marked

Spool

GUN or TIG Torch

and connect gas line from

Cylinder and Regulator as shown in Figure A.5.

5. Connect the remote control receptacle from the

Foot Amptrol(Optional) to the remote control recep-
tacle on the machine.

WARNING

POWER MIG

350MP

Содержание Power MIG 350MP
















































Результаты поиска

Содержание Power MIG 350MP

Отзывы:

Бренды по названию

Популярные бренды

Lincoln Electric Power MIG 350MP, Руководство оператора

Результаты поиска

Содержание Power MIG 350MP

Отзывы:

Бренды по названию

Популярные бренды