background image

Page 12 of 32

Misc. on the DESKLINE

®

 DL5 IC / DL6 IC / DL15 IC / DL16 IC system

This system is a DESKLINE system developed for desks and for indoor use in offices. Do not use it in industrial kitchens or in 
other enviroments that have to be cleaned with aggressive detergents.
Do not bolt the legs to the floor so that free movement is prevented. This could cause serious damage to the legs in fault 
situations.

Warranty 

This DESKLINE product is subject to warranty pursuant to the terms of LINAK DESKLINE Warranty Paper, available on the LINAK 
website 

www.linak.com/warranty.

Maintenance

Clean dust and dirt on the outside of the system at appropriate intervals and inspect them for damage and breaks.
Inspect the connections, cables, and plugs and check for correct functioning as well as fixing points. 

Service of double-insulated products:  

Class II 

A Class II or 

double insulated 

electrical appliance is one which has been designed in such a way that it does not require a 

safety electric earth connection (US: ground).
The basic requirement is that no single failure can result in dangerous voltage becoming exposed so that it might cause an 
electric shock and that this is achieved without relying on an earthed metal casing. This is usually achieved at least in part by 
having two layers of insulating material surrounding live parts or by using reinforced insulation.
There is no earthing/grounding means provided on the product, and no earthing/grounding means is to be added to the 
product.
In Europe, a double insulated appliance must be labelled “Class II”, “double insulated” or bear the double insulation symbol 
(a square inside another square).
Servicing a double-insulated product requires extreme care and knowledge of the system, and is to be done only by qualified 
service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace.

Cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).

Содержание DESKLINE DL15 IC


































Отзывы: