LIMBACH L 2000 DA Скачать руководство пользователя страница 45

Страница: 45 / 48

Page: 45/48

Operating Manual L 2000

Edition: 01.03.2016

201

Possible Cause:

Remedy:

Fuel tank empty (faulty indication of fuel
gauge).

Refuel, replace fuel gauge.

Fuel valve closed or filter locked.

Open fuel valve, clean or replace filter.

Fuel line defective or not connected.

Replace or connect fuel line.

Fuel pump defective.

Repair or replace fuel pump.

Induction system leakage.

Check induction system for leakage and
replace, if necessary, tighten joints.

Carburetor contaminated or locked.

Clean carburetor.

Choke not operated to its stop (cold engine).

Operate choke and check as necessary.

12.2 Engine Operating Trouble

The following phenomena are considered to be engine operating trouble:

•

uneven and irregular engine run

•

temporary interruptions

•

low power

•

engine overheat

•

rough engine run

Consider reasons as per section 12.1 besides the ones listed below.

12.2.1 Fuel Supply

Possible Cause:

Remedy:

Insufficient fuel flow (Fuel ventilation lokked,
lines blocked or defective, filter or
screens blocked).

Check tank ventilation, lines, filter and
screens and replace as necessary.

Insufficient fuel pump pressure.

Check fuel pump pressure and correct, if
necessary.

Fuel pump defective.

Repair or replace fuel pump.

Float valve contaminated, jammed or
worn.

Clean or replace float valve.

Wrong carburetor float level.

Adjust float level.

Содержание L 2000 DA

















































Результаты поиска

Содержание L 2000 DA

Отзывы:

Бренды по названию

Популярные бренды

LIMBACH L 2000 DA, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание L 2000 DA

Отзывы:

Бренды по названию

Популярные бренды