manualshive.com logo in svg

LIMBACH L 2000 DA, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
LIMBACH L 2000 DA Скачать руководство пользователя страница 34

 

 

 

Page: 34/48 

Operating Manual L 2000 

Edition: 01.03.2016 

201

.2

5

3

.9

0

5

.0

0

0

 

Check valve clearance and readjust, if necessary. 
 
Mount cylinder head cover. 

 
Check gaskets and replace as necessary. 
 

8.14  Cleaning, Check and Setting of Spark Plugs 

 
Removal of spark plugs. 
 

Disconnect spark plug connectors.  
Unscrew connectors on shielded spark plugs. 

 

 

Caution: 
Do not unscrew spark plugs when the engine is hot. 

 
Cleaning of spark plugs. 

 
Clean spark plugs by means of a plastic brush in a degreasing solution. Do not use a 
steel or brass brush for cleaning. Do not sandblast spark plugs. 

 
Check electrode gap and adjust, if necessary (not for spark plug LB-N41.0 and LB-L41.0). 

 
Check electrode gap with a nozzle gauge and correct by bending the ground electrode(s) 
 
The electrode gap is 0.4 to 0.5 mm. 

 
Install spark plugs, reattach spark plug connectors. 
 

Grease spark plug thread with graphite grease P/N: 170.210.010. 
Torque 25 Nm. 

 

 

Caution: 
Electrodes must always be free from graphite grease! Do not use copper paste.

 

 
 
Approved spark plugs. 

Se 

„Technical Data“. 

 
It is recommended to change spark plugs every 150 operating hours. 

 
Note: 

The condition of the spark plugs removed from the engine discloses the following information: 
 
Light grey: 

 

Spark plug and engine adjustment o.k. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание L 2000 DA

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды