Lika MTA1 Скачать руководство пользователя

Страница: 36 / 48

SMA1

WARNING

As soon as the

Load and save default parameters

command is sent, all

parameters which have been set previously are overwritten, thus previously set
values are lost!

As soon as the command is sent, the register is set back to "00" (

Normal

operation

) automatically.

Wait min. 30 ms (EPROM writing time) before using a new function.
Default = 00 (

Normal operation

)

Configuration

[49, rw]

Bit

Function

bit=0

bit=1

Not used

Set preset / offset

Preset

Offset

Enable preset / offset Enable

Disable

Not used

Output code

Gray

Binary

Counting direction

Standard

Inverted

Not used

: it affects the absolute position information, not the sine/cosine signals

Set preset / offset

This parameter is available only if the

Enable preset / offset

parameter is set to

ENABLE. It allows to activate either the preset function (

Set preset / offset

PRESET) or the offset function (

Set preset / offset

= OFFSET); the Preset or

Offset value has to be set in the

Preset / Offset

the preset / offset functions (

Enable preset / offset

= ENABLE), this item allows

to activate either the preset function or the offset function. The value set in the

Preset / Offset

of this parameter whether it is set to PRESET (0) or OFFSET (1). In the first case
(

Set preset / offset

= PRESET) the

Preset / Offset

preset value; while in the second case (

Set preset / offset

= OFFSET) the

Preset

/ Offset

value use the

Save and activate Preset / Offset

function in the

Command

Preset /

Offset

Default = 0 (Preset)

Enable preset / offset

It enables / disables the preset / offset functions. After having enabled the use of
the functions you have to choose whether to activate the preset or the offset in

MAN SMA1 E 2.9.odt

7 - BiSS C-mode interface

36 of 48

Содержание MTA1

















































Результаты поиска

Содержание MTA1

Отзывы:

Похожие инструкции для MTA1

Бренды по названию

Популярные бренды

Lika MTA1, Руководство пользователя

Результаты поиска

Содержание MTA1

Отзывы:

Похожие инструкции для MTA1

Бренды по названию

Популярные бренды