LEVER
STEM
POWER
STEM
POWER
BEAD
TRACK
Fig. 11
Retain these instructions for maintenance reference.
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
To assure full compliance with local codes and regulations, check with your local electrical inspector
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
INSTRUCTION SHEET NO.
A0101
Page 2 of 4
Do not try to move stationary silver contact.
OPERATE ON 2 CIRCUIT ADVENT LYTESPAN TRACK:
PowerWash T5 POWER STEM ATTACHMENT FITTING TO
INSTRUCTIONS FOR CONVERTING SUSPENDED
on BLACK SPACER as shown in Fig. 14 & 15.
line) by pulling CONTACT as high as stop permits and slipping
raise BRASS CONTACT to high position (as indicated by dotted
To convert power stem attachment fitting for upper circuit,
UPPER CIRCUIT, Fig. 14, 15, & 16:
SPACER in place for lower circuit.
Illustrates BRASS CONTACT in low position with BLACK
LOWER CIRCUIT, Fig. 13 & 16:
LYTESPAN TRACK SYSTEM. FOR USE WITH LYTESPAN TRACK SYSTEMS ONLY.
INSTRUCTIONS FOR ATTACHING SUSPENDED PowerWash T5 POWER STEM TO A
LYTESPAN TRACK
PowerWash T5 POWER STEM TO SINGLE CIRCUIT
INSTRUCTIONS FOR ATTACHING SUSPENDED
using POWER STEM LEVER.
4. To remove: rotate POWER STEM 90fl counterclockwise
with TRACK. See Fig. 12.
STEM LEVER. POWER STEM LEVER should be parallel
3. Rotate POWER STEM 90fl clockwise using POWER
must be on the same side as the track BEAD. See Fig. 11.
2. Insert POWER STEM into TRACK. The POWER STEM LEVER
1. Turn off power to TRACK.
operating PowerWash T5 on Single Circuit Track.
must be used at all times. The BLACK SPACER is not used when
on Two Circuit Lytespan Track, the BLACK SPACER (provided)
NOTE: To insure proper operation of PowerWash T5 suspension
TM
NOTE: Not for use with ProSpec Track.
Fig. 12
Fig. 13
Fig. 15
NEUTRAL
CIRCUIT
LOWER
CIRCUIT
UPPER
Fig. 16
ASSEMBLY
PLUG
SPACER
BLACK
CONTACT
BRASS
MOVABLE
SPACER
BLACK
ASSEMBLY
PLUG
(Neutral)
CONTACT
STATIONARY
CONTACT
BRASS
MOVABLE
ASSEMBLY
PLUG
SPACER
BLACK
CONTACT
BRASS
MOVABLE
Fig. 14
®
®
SPRINGS
BOTTOM
GROOVE
BOTTOM
Fig. 18
GROOVE
TOP
FRONT STEP
LOUVER
Fig. 19
Fig. 20
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
To assure full compliance with local codes and regulations, check with your local electrical inspector
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
Page 3 of 4
A0101
INSTRUCTION SHEET NO.
Retain these instructions for maintenance reference.
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
LOUVER:
INSTRUCTIONS FOR INSTALLING A PowerWash T5
away from the luminaire (see Fig. 19).
4. To remove, push down the TOP SPRING TABS and rotate
into the TOP GROOVE (see Fig. 17, 19, & 20).
FRONT STEP on the luminaire. Release the TOP SPRING TABS
toward the TOP GROOVE in the luminaire until it hits the
3. While pushing down TOP SPRING TABS, rotate LOUVER
BOTTOM GROOVE in the luminaire (see Fig. 17 & 18).
2. First insert BOTTOM SPRINGS on the LOUVER into the
1. Turn off power to TRACK.
for safe operation (see Fig. 20).
NOTE: Ensure that all four LOUVER SPRINGS are fully engaged
NOTE: Luminaire may be used without LOUVER if desired.
INSTRUCTIONS FOR INSTALLING A PowerWash T5 LOUVER
TM
SPRING TAB
SPRINGS
BOTTOM
Fig. 17
SPRINGS
TOP
IS: 9279
IS: 9279
