CAVITY
TRACK
Fig. 3
LOCK TO LOWER
CABLE; DEPRESS
HOLD THIS
RAISE
PULL TO
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
To assure full compliance with local codes and regulations, check with your local electrical inspector
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
Page 1 of 4
A0101
INSTRUCTION SHEET NO.
Retain these instructions for maintenance reference.
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
WARNING: Do not damage WHITE, BLACK, or GREEN insulation.
be removed.
NOTE: To reposition HOUSING, HOUSING COVER does not have to
pull CABLE down. See. Fig 3.
NOTE: To lower luminaire, hold CABLE, depress CABLE LOCK, and
PRIOR TO WIRING.
WARNING: Do not attach POWER STEM BASE into TRACK
INSIDE TRACK CAVITY (see Fig. 3).
POWER TO TRACK. NEVER PLACE AIRCRAFT CABLE
WARNING: TO PREVENT ELECTRIC SHOCK, TURN OFF
using HOUSING SCREWS. See Fig. 10.
8. Fasten POWER STEM HOUSING to POWER STEM BASE
BLACK WIRE to BRASS SCREW
WHITE WIRE to SILVER SCREW
7. Connect: GREEN WIRE to GREEN SCREW MARKED "GND"
6. Twist strands of wire together and form a "J" loop. See Fig. 10.
5. Tie knot in CORD as shown in Fig. 9.
4. Strip CORD and WIRES to lengths shown in Fig. 9.
3. Pull CORD through POWER STEM HOUSING. See Fig. 9.
If CORD RETAINERS are not used, cut off. See Fig. 8.
standard TIE WRAP (local hardware item) may also be used.
CORD through RETAINERS and position where needed. A
2. If a CORD RETAINER is desired, two are provided. Pull
it up to the TRACK and cutting. See Fig. 7.
1. Leaving slack, CORD length can be determined by bringing
PowerWash T5 POWER STEM:
INSTRUCTIONS FOR WIRING SUSPENDED
TM
HOUSING 90fl counter clockwise. See Fig. 2.
8. To remove or reposition on track, rotate SUSPENSION
HOUSING as shown in Fig. 6.
7. Slide up HOUSING COVER and snap onto SUSPENSION
COPPER STOP (provided) onto AIRCRAFT CABLE. See Fig. 5.
CABLE leaving approx 1/2" above CABLE LOCK. Crimp
in Fig. 4. If no adjustment will be desired, cut AIRCRAFT
BODY and pinned down using HOUSING SLOTS as shown
feet of AIRCRAFT CABLE can be wrapped around HOUSING
6. If future suspension length adjustment is desired, up to two
CABLES through CABLE LOCK. See Fig. 3.
5. Adjust suspension length and leveling by pulling AIRCRAFT
4. Rotate SUSPENSION HOUSINGS 90fl clockwise. See Fig. 2.
Fig. 2.
bottom of HOUSING pointing toward BEAD on TRACK. See
3. Insert SUPSENSION HOUSINGS into TRACK with ARROW on
CABLE LOCK. See Fig. 1.
pull AIRCRAFT CABLE through, leaving approx 1" above
2. Unwrap AIRCRAFT CABLE. While depressing CABLE LOCK,
See Fig. 1.
1. Remove WARNING LABEL on SUSPENSION HOUSING.
T5 SUSPENSION HOUSING TO LYTESPAN TRACK:
INSTRUCTIONS FOR ATTACHING SUSPENDED PowerWash
A LYTESPAN TRACK SYSTEM. FOR USE WITH LYTESPAN TRACK SYSTEMS ONLY.
INSTRUCTIONS FOR ATTACHING SUSPENDED PowerWash T5 SUSPENSION HOUSING TO
NOTE: Not for use with ProSpec Track.
WARNING: If Mounting on wall or sloped ceiling, COPPER STOP must always be used
Fig. 5
STOP
COPPER
ARROW
CABLE
AIRCRAFT
SLOTS
HOUSING
BODY
HOUSING
Fig. 4
HOUSING
SUSPENSION
BEAD
TRACK
Fig. 2
HOUSING SCREWS
STEM BASE
POWER
POWER STEM HOUSING
(GREEN WIRE)
GREEN "GND" SCREW
(WHITE WIRE)
SILVER SCREW
(BLACK WIRE)
BRASS SCREW
WIRES
Fig. 10
3/4"
1/4"
2
3/4"
15/16"
1
WIRES
POWER STEM HOUSING
CORD
GREEN
WHITE
BLACK
Fig. 9
RETAINER
CORD
CORD
Fig. 8
CORD
TRACK
Fig. 7
COVER
HOUSING
Fig. 6
1"
CABLE LOCK
LABEL
WARNING
CABLE
AIRCRAFT
Fig. 1
Fig. 22
Fig. 21
LAMPS
SOCKETS
BRACKET
SOCKET
SOCKETS
BRACKET
SOCKET
Retain these instructions for maintenance reference.
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
To assure full compliance with local codes and regulations, check with your local electrical inspector
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
INSTRUCTION SHEET NO.
A0101
Page: 4 of 4
MAKING ANY ADJUSTMENTS!
CAUTION: ALLOW TIME FOR LUMINAIRE TO COOL BEFORE
rotates 360fl.
DOING SO MAY CAUSE AN ELECTRICAL HAZARD). HEAD
rotation stops (DO NOT FORCE LUMINAIRE PAST STOPS.
Rotate HEAD of luminaire to desired position. Luminaire has
SEE LABEL ON LUMINAIRE FOR PROPER WATTAGE.
WARNING: USE PROPER WATTAGE T5 HIGH OUTPUT LAMPS ONLY.
AIMING INSTRUCTIONS (see Fig. 23)
TM
remove from SOCKET.
7. To remove LAMP, repeat steps 1-3. Rotate LAMP(s) 90fl and
(see Fig. 22).
6. Push SOCKET BRACKETS back into their original position
5. For two LAMP luminaire, repeat step 4 for the second LAMP.
in place.
4. Insert LAMP into SOCKET and rotate LAMP 90fl locking it
required. Pull with hands.
3. Slide out both SOCKET BRACKETS (see Fig. 21). No tools
2. Remove LOUVER (see Page 3).
1. Turn off power to track.
PowerWash T5 LUMINAIRE:
INSTRUCTIONS FOR LAMPING A SUSPENDED
INSTRUCTIONS FOR LAMPING AND OPERATING A SUSPENDED PowerWash T5 LUMINAIRE.
will extinguish when one fails.
Assure that both lamps are properly installed. Also, both lamps
NOTE: A two lamp luminaire will not operate with only one lamp.
Fig. 23
HEAD
IS: 9279
IS: 9279
