Light Efficient Design Solera SL-SAL-OG Скачать руководство пользователя страница 1

LIGHT EFFICIENT DESIGN HEADQUARTERS 

188 S. Northwest Highway 

 Cary, IL 60013

INNOVATION & MANUFACTURING CENTER 

30 Log Bridge Road, Building 200 

 Middleton, MA 01949

847.380.3540 

 led-llc.com

04.08.22 Information is subject to change without notice.

READ CAREFULLY BEFORE INSTALLING THE FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE

Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper 

grounding is required for safety. This product must be installed in accordance with the applicable installation code 

by a person familiar with the construction and operation of the product and hazards involved.

PLEASE NOTE THAT THE PERFORMANCE OF A SOLAR LIGHT DEPENDS ON MANY FACTORS INCLUDING 

SOLAR RADIATION, TEMPERATURE, AND OTHER ENVIRONMENTAL FACTORS. DIRTY SOLAR PANELS CAN 

SIGNIFICANTLY REDUCE THE CHARGE EFFICIENCY OF SOLAR PANELS. IMPROPER ALIGNMENT OF THE 

PANEL, SHADOWS, OR OBSTACLES THAT BLOCK DIRECT SUNLIGHT TO THE SOLAR PANEL CAN CAUSE 

POOR PERFORMANCE.  
NOTE: THE BATTERY IS DISCONNECTED UNTIL THE 4 PIN CONNECTOR FOR THE SOLAR PANEL 

IS CONNECTED. THE LIGHT WILL NOT OPERATE UNLESS THE SOLAR PANEL OR A CHARGER ARE 

CONNECTED. 
DO NOT OPEN THE FIXTURE HOUSING, AS THERE ARE NO USER SERVICEABLE PARTS INSIDE. IF BATTERY 

REPLACEMENT IS REQUIRED, PLEASE CONTACT THE MANUFACTURER.

STEP 1: REMOVE THE CONTENTS FROM ALL THE CARTON

Please be sure to check that everything is in the box.

OG/HYBRID 365 AREA LIGHT 

SL-SAL-OG/HYB-50W-XXK-SF-G2

SOLAR

LIGHTS

INSTRUCTIONS

1  x  Remote  (CU-ALL6)         

2 x AA Batteries

1 x Manual

1 x 5mm allen wrench 

1 x 6mm allen wrench

1 x Fixture

1 x Slipfitter

*(4 set screws pre attached)

STEP 2: SLIPFITTER MOUNTING

a. Adjust the angle of the fixture. Align the white      

    lines w/ numbers and the arrows on the fixture. 

    Loosen the screws and swivel the fixture to the       

    desired angle, then re-tighten the screws.
b. The slipfitter mounting fits a 2 3/8” O.D. tenon.   

     Place the slipfitter over the tenon and secure the  

     fixture with the two set screws on the side of the  

     slipfitter.

Содержание Solera SL-SAL-OG

Страница 1: ...EL SHADOWS OR OBSTACLES THAT BLOCK DIRECT SUNLIGHT TO THE SOLAR PANEL CAN CAUSE POOR PERFORMANCE NOTE THE BATTERY IS DISCONNECTED UNTIL THE 4 PIN CONNECTOR FOR THE SOLAR PANEL IS CONNECTED THE LIGHT WILL NOT OPERATE UNLESS THE SOLAR PANEL OR A CHARGER ARE CONNECTED DO NOT OPEN THE FIXTURE HOUSING AS THERE ARE NO USER SERVICEABLE PARTS INSIDE IF BATTERY REPLACEMENT IS REQUIRED PLEASE CONTACT THE MA...

Страница 2: ... AREA LIGHT SL SAL OG HYB 50W XXK SF G2 SOLAR LIGHTS INSTRUCTIONS STEP 4 INSTALL SOLAR PANEL KIT Install solar panel kit model SL SAL 50W 2PANELKIT This comes in a separate carton Installation instructions for the solar panel kit are included in the carton or are available on the solera solar website STEP 5 CONNECT SOLAR PANEL TO FIXTURE Once the fixture is completely installed plug the cable from...

Страница 3: ...24ft b The fixture will operate in the default mode without using the remote c You may want to adjust the settings based off your geographical area to attain more solar powered operation rather than pulling from the grid We can change the settings by following the below DEFAULT OPERATING MODE a For the first 2 hours the product runs at 80 fixed output b The next 12 hours it will run it at 50 idle ...

Страница 4: ...nimum angle of 15 degrees 4 Adjust the angle of the panel to optimize exposure to sunlight Avoid north facing panels in the USA 5 The fixture will be active once the solar panel is connected to the fixture s solar panel connector wire 6 Please make sure that the panel is installed under direct sunlight The red light should be flashing indicating that it is charging 7 The lighting fixture will auto...

Отзывы: