background image

2

Observe the following prior to use of the treadmill:
DANGER: To reduce the risk of electric shock, please observe the following:

z

Always unplug the treadmill from the electrical outlet immediately after using and before cleaning, assembling, or servicing.

NOTE: Failure to follow these instructions may lead to personal injury and cause damage to the treadmill.
WARNING: 
To reduce the risk of burns, fire, electric shock please observe the following:

z

Never leave the treadmill unattended when plugged in. Disconnect by turning off the master power switch, and unplugging from outlet.

z

Never operate this treadmill if it has a damaged cord or plug, is not working properly, if it has been dropped or damaged, or if it has been
exposed to water.

z

Do not attempt any maintenance or adjustments other than those described in this manual. Should any problems arise, discontinue use and
consult the Authorized Service Representative.

z

Do not use outdoors.

z

Do not operate where aerosol (spray can) products are being used or where oxygen is being administered.

z

Do not pull the treadmill by its power cord or use the cord as a handle.

z

Close supervision is necessary if this treadmill is used by, or near children, persons with disabilities, or pets.

z

Keep Dry-do not operates in a wet or moist condition. Save these instructions.

z

Do not operate under a blanket. Excessive heating can occur and cause fire, electrical shock, or injury to 
persons.

z

Keep electrical cord away from heated surfaces.

z

Never insert any object into any opening.

z

Keep the treadmill on a solid, level surface with sides at least two feet from any wall. Be sure the area around

the treadmill remains clear during use and has adequate clearance, see illustration below.

WARNING: Connect the treadmill to a properly grounded outlet only.                 

FRONT

REAR

TOP

VIEW

2 FEET MIN.

2 FEET MIN.

4 FEET MINIMUM

LEFT

SIDE

RIGHT

SIDE

SAFETY

INSTRUCTIONS

Содержание 97355


















Отзывы: