background image

Page | 21  

 

Care and Maintenance

 

 

 

The LifeCore 950RBs is made from the best materials and has been tested and received a quality 
control review prior to its packaging to ensure the correct parts and proper fitting of each component.  
The amount of maintenance required is very little and very simple; however, a failure to implement 
preventative  maintenance  suggestions  can  prevent  the  machine  from  operating  as  designed.  The 
950RBs is only for indoor use and should not be stored in damp, extremely cold or hot areas as this 
will damage the unit this voiding the warranty. 
 
Always inspect hardware prior to any exercise session. Look for loose hardware, loose pedals, loose 
cranks and frayed wires. Repair or replace any damaged or worn parts, tighten all loose hardware. 
 
 

 

  Always clean the machine after use.  

 

1)  Proper cleaning is important for longevity of a machine, clean the unit with a light soap 

water mixture, follows by a dry towel, or uses a light house hold cleaner such as Windex 
to remove dirt. The purpose of cleaning the unit is to remove body sweat which contains 
salt. Salt is the number one factor that will cause the unit to rust and the electronics to 
stop working. 
 

2)  Dry the unit off with a clean towel to remove left over moisture after every use. 

 

3)  To clean pads, use a mild soap and warm water. 

 
 

  As  part  of  LifeCore’s  normal  installation  and  set-up  process,  all  pedal  cranks  must  be 

tightened after 8 to 10 hours of initial riding to ensure parts are properly seated to axle. This 
is standard initial “break-in” service, which must be performed after the first 8 to 10 hours of 
use.  Un-tightened  pedal  cranks  may  become  loose,  causing  damage,  which  may  void  the 
warranty. 
 
 

  After the first 12 hours of use, check and retighten any bolts, nuts, screws, etc. making sure 

that they are tight and working properly.  
 

1)  The number one service issue is loose hardware. Loose hardware can cause the unit to 

tick,  creak,  thump, knock,  etc.  After  the  first  12  hours  once  all  the  hardware  has  been 
tightened, the hardware should be checked every 3 months. 
 
 

  Only use the appropriate power source, never use an adapter that is not certified for the unit, 

a wrong adapter will cause the electronics to overheat and malfunction.  
 
 

 
In  the  unlikely  event  that  the  950RBs  experiences  a  problem,  please  contact  LifeCore  fitness  for 
advice toll free at 888-815-5559. 
 
 

 

Содержание LC-950RBs


























Отзывы: