background image

CAF-03

0606

Congratulations on your selection of the Lifebreath Clean
Air Furnace. This is a very advanced unit that combines
an electric furnace with the tremendous health benefits of
year-round fresh air ventilation in every room of your
house.

With the addition of Lifebreath T.F.P. Air Cleaner (option-
al) you will have the ultimate in comfort and healthy indoor
air quality. (See back cover of this manual)

Once it is correctly installed, safety will never be an issue
with your Lifebreath furnace. No flames, fumes or flue
gases to be concerned about.

This Operating and Installation Guide will help you learn
about your Lifebreath Clean Air Furnace quickly and easi-
ly. The table of contents will show you where to find
information on every feature of this unit along with easy to
understand operating instructions. If, however, you do
encounter a question that is not covered in this Guide you
should call the Lifebreath dealer who installed your fur-
nace. Chances are that he will be able to give you a
satisfactory answer but if he is unable to do so then we
invite you to contact us directly.

The purpose of this manual is to act as an
installation guide only for the Lifebreath Clean Air
Furnace.

All national and local code requirements must be met
when installing a Lifebreath Clean Air Furnace. Be sure to
consult the proper authorities.

Introduction ......................................................................1

Table of Contents.............................................................1

General ............................................................................1

Specifications................................................................2-4

Installation...................................................................5-10

Wiring Diagram ..............................................................11

Start-up Procedure.........................................................12

Operation .......................................................................13

Troubleshooting .............................................................14

Maintenance and Service Record ..................................15

Introduction

General

Table of Contents

Model 60ELE

“ELECTRIC” CLEAN AIR FURNACE MANUAL

Содержание 60ELE-DF

















Отзывы: