Lifebreath 1230 ERV страница 24 Скачать руководство пользователя

Страница: 24 / 35

www.lifebreath.com

EFROST

The 330, 530, 730, and 1230 units are equipped with an electronically controlled fan defrost system to remove

frost that collects on the warm air side of the heat exchanger core. When the outside air temperature drops

below 27°F (-3°C), defrost is activated which provides for an automatic defrost cycle. During the automatic

defrost cycle the fresh air supply is shut off while the exhaust fan continues to operate. This allows warm

inside air to flow through the heat exchanger core melting frost accumulation. After the defrost period, the

fresh air supply fan automatically returns to the normal speed and fresh outside air continues to be drawn into

the building. The defrost cycle repeats automatically until the air temperature rises above 27°F (-3°C).

•

If the indoor air temperature is too low, the defrost time may need to be increased.

•

The unit must be mounted level (horizontal) to obtain proper drainage of water from the heat

exchange cores. The warranty will be void if these conditions are not met.

Defrost Time Adjustment

DIP switch #8 (located on the Aircom circuit board) will adjust the defrost time. Do not change to any other

DIP switch configuration.

Factory Setting (DIP switch #8 OFF)

The sequence of events for this defrost mode at

27°F (-3°C) is:

Both fans will stop for one minute.

The ERV exhaust motor will initiate and

operate for 4 minutes.

Both ERV motors (exhaust and intake)

will operate for 30 minutes.

The cycle repeats.

Increased Defrost Time (DIP switch #8 ON)

Cooler climates may require a more aggressive

defrost cycle:

Both fans will stop for one minute.

The ERV exhaust motor will initiate and

operate for 4 minutes.

Both ERV motors (exhaust and intake)

will operate for 20 minutes.

The cycle repeats.

Caution

•

Change DIP switch only as illustrated on this page. Do not adjust any other switches.

Содержание 1230 ERV




































Результаты поиска

Содержание 1230 ERV

Отзывы:

Похожие инструкции для 1230 ERV

Бренды по названию

Популярные бренды

Lifebreath 1230 ERV, Руководство по установке

Результаты поиска

Содержание 1230 ERV

Отзывы:

Похожие инструкции для 1230 ERV

Бренды по названию

Популярные бренды