Lifebreath 1230 ERV Скачать руководство пользователя

Страница: 2 / 35

www.lifebreath.com

Pre-Installation Notes

Note

•

Due to ongoing research and product development, specifications, ratings, and dimensions are

subject to change without notice. Refer to

www.lifebreath.com

for the latest product

information.

Attention

•

Do not apply electrical power to the unit until after the completion of the installation (including

installation of low voltage control wiring).

•

Ensure the installation and wiring is in accordance with all local electrical codes.

•

Plug the unit into a standard designated (120 VAC) electrical outlet with ground.

•

The use of an extension cord with this unit is not recommended. If the installation requires

further wiring, have a licensed electrician make all the electrical connections. The

recommended circuit is a separate 15 A/120 V circuit.

Caution

•

Before installation, careful consideration must be given to how this system will operate if

connected to any other piece of mechanical equipment, i.e. a forced air furnace or air handler,

operating at a higher static. After installation, the compatibility of the two pieces of equipment

must be confirmed, by measuring the airflows of the ERV, by using the balancing procedure

found in this manual. Never install a ventilator in a situation where its normal operation, lack of

operation or partial failure may result in the back drafting or improper functioning of vented

combustion equipment

•

Unit must be installed level to ensure proper condensate drainage. Due to the broad range of

installation and operational conditions, consider the possibility of condensation forming on

either the unit or connecting ducting. Objects below the installation may be exposed to

condensate.

•

Do not install control wiring alongside electrical wire.

Warning

•

Disconnect the power from the unit before cleaning or servicing.

•

To prevent electrical shock, it is extremely important to confirm the polarity of the power line

that is switched by the safety (disconnect) switch. The hot line (black) is the proper line for

switching. Use either a voltmeter or test lamp to confirm the absence of a voltage between the

disconnect switch and ground (on the cabinet) while the door is open. This procedure must be

followed, as dwellings are occasionally wired improperly. Always ensure the proper grounding

of the unit.

•

Improper installation, adjustment, alteration, service or maintenance can cause property

damage, personal injury or loss of life. Installation and service must be performed by a

qualified installer or service agency.

Содержание 1230 ERV




































Результаты поиска

Содержание 1230 ERV

Отзывы:

Похожие инструкции для 1230 ERV

Бренды по названию

Популярные бренды

Lifebreath 1230 ERV, Руководство по установке

Результаты поиска

Содержание 1230 ERV

Отзывы:

Похожие инструкции для 1230 ERV

Бренды по названию

Популярные бренды