GSC3218JN Gas Grill
GSC3218JN owner’s manual
12
Check For Leaks
Make (2-3) oz. 0-90ml of leak solution by mixing one part liquid dishwashing soap with three parts water.
Make sure control knobs are off.
Spoon several drops of solution at all gas connections.
Inspect the solution at the connection, looking for bubbles, bubbles will appear if connections are not properly sealed. Tighten or repair as necessary.
Retest with solution. If you continue to see bubbles,disconnect gas, turn off the gas at the source, disconnect gas line from grill and immediately call
qualified service person.
Lighting Your Grill
Danger: Failure to open lid while igniting the barbecue’s burners or not waiting 5 minutes to allow the gas to clear if the
barbecue does not light, may result in an explosive flame-up which can cause serious bodily injury or death.
Main Burner
1.
Open lid during lighting burners.
Attempting to light the burner with the lid closed may cause an explosion! Make sure there are no obstructions of airflow to the gas unit. Spiders
and insects can nest within and clog the burner / venturi tube at the orifice.
A clogged burner tube can lead to a fire beneath the appliance.
2.
All valves must be in the OFF position.
3.
Turn gas ‘’ ON’’ at manual valve
4.
Ignite only the burners you desire to use, using the same method for each: Push in desired burner valve knob fully and rotate slowly about 1/4 turn
counter-clockwise until a click is heard and this will light the burner. If the burner does not light, immediately return the valve knob to OFF, wait five
minutes for the gas to clear and repeat the procedure. repeat the same procedure with any other burner desired. After burner ignites, repeat the
same procedure with any other burner desired.
5.
Adjust valve knob(s) to desired cooking setting.
Match Lighting the Main Burners:
1.
Remove cooking grid from burner you desired to light.
2.
Insert a lit match attached to the end of the Lighting Rod (provided with the grill) placing flame under heating plate near to burner ports.
3.
Press in valve knob and rotate counter clockwise to Hi setting and burner should light immediately. If more than one burner is desired, repeat
procedure with each burner.
4.
Replace cooking grid and adjust burners to desired cooking settings.
Option-Left and right main burners can be lit by inserting a lit match attached to the end of the Lighting Rod through holes on either side as
desired.
After lighting, please observe the burner flame, make sure all burner ports are lighted.
If burner flame goes out during operation, immediately turn the gas “off” and open lid to let the gas clear for about 5 minutes before re-lighting.
Before cooking on this grill for the first time, operate the grill for about 15 minutes with the lid closed and the gas turned on “high.” This will “heat clean”
the internal parts and dissipate odor from the manufacturing processes and painted finish.
Clean your grill after each use, DO NOT use abrasive or flammable cleaners, as it will damage the parts of this product and may start a fire.
Side Burner
Shutting Off Burners
:
1. Always turn the valve knob(s) clockwise to the High position, then depress and turn it to OFF.
Never force the knob without depressing it as that can damage the valve.
2. Promptly turn the gas supply OFF at the manual valve
3.
Close the lid of the grill.
1. Open lid during lighting burner. Lid must be open when burner is on.
2. Valve must be in the “off” position
3. Turn gas ‘’ON’’ at manual valve
4. Push in side burner valve knob fully and rotate slowly about 1/4 turn counter-clockwise until a click is heard and this will light the burner. If the
burner does not light, immediately return the valve knob to OFF, wait five minutes for the gas to clear and repeat the procedure.
5. After burner ignites, adjust valve knob to desired cooking setting.
