5
A
SSEMBLING THE
T
READMILL
Tools Required: Metric Wrench Set, Metric
Allen Wrench Set, Phillips Screwdriver
1.
Locate the USER LEFT UPRIGHT (A) (upright with
pre-fed CONSOLE CABLE). With the HANDLEBAR
EXTENSION facing the rear of the unit, position the
USER LEFT UPRIGHT near the USER LEFT
UPRIGHT BRACKET (B). Connect the CONNEC-
TORS (C) leading from the USER LEFT UPRIGHT
and USER LEFT UPRIGHT BRACKET. Slide the
USER LEFT UPRIGHT over the USER LEFT
UPRIGHT BRACKET until fully seated. Install one
5/8" BUTTON HEAD SCREW (1) and LOCK
WASHER (2) each in the side and rear mounting
holes of the USER LEFT UPRIGHT. Finger-tighten
the SCREWS.
Caution:
Do not pinch the cable when sliding
the USER LEFT UPRIGHT (A) over the USER
LEFT UPRIGHT BRACKET (B).
2.
Locate the USER LEFT UPRIGHT BRACE (D).
Using four 5/8" BUTTON HEAD SCREWS (1) and
LOCK WASHERS (2), secure the USER LEFT
UPRIGHT BRACE to the front of the USER LEFT
UPRIGHT (A) and the FRAME (E). Finger-tighten
the SCREWS.
3.
Locate the USER RIGHT UPRIGHT (F). With the
HANDLEBAR EXTENSION facing the rear of the
unit, position the USER RIGHT UPRIGHT near the
USER RIGHT UPRIGHT BRACKET (G). Slide the
USER RIGHT UPRIGHT over the USER RIGHT
UPRIGHT BRACKET until fully seated. Install one
5/8" BUTTON HEAD SCREW (1) and LOCK
WASHER (2) each in the side and rear mounting
holes of the USER RIGHT UPRIGHT. Finger-tighten
the SCREWS.
4.
Locate the USER RIGHT UPRIGHT BRACE (H).
Using four 5/8" BUTTON HEAD SCREWS (1) and
LOCK WASHERS (2), secure the USER RIGHT
UPRIGHT BRACE to the front of the USER RIGHT
UPRIGHT (F) and the FRAME (E). Finger-tighten
the SCREWS.
5.
Locate the HANDRAIL (J). With the stepped exten-
sion end of the HANDRAIL facing right, position the
HANDRAIL between the LEFT and RIGHT
UPRIGHTS (A) & (F) at the HANDRAIL MOUNTING
HOLES. Secure the user left side of the HANDRAIL
to the LEFT UPRIGHT using the 2" BUTTON HEAD
SCREW (3) and one LOCK WASHER (2). Secure
the user right side of the HANDRAIL to the RIGHT
UPRIGHT using one 5/8" BUTTON HEAD SCREW
(1) and one LOCK WASHER (2).
6.
Locate the DISPLAY CONSOLE (K). Position the
DISPLAY CONSOLE near the top ends of the LEFT
and RIGHT UPRIGHTS (A) & (F). Connect the
CONNECTOR (L) leading from the top of the USER
LEFT UPRIGHT to the CONNECTOR (L) leading
from the user left side of the DISPLAY CONSOLE.
Slide the DISPLAY CONSOLE onto the TOP
UPRIGHT EXTENSIONS. Secure the DISPLAY
CONSOLE to the uprights using two 5/8" BUTTON
HEAD SCREWS (1) and LOCK WASHERS (2) on
either side of the DISPLAY CONSOLE. Tighten the
SCREWS securely.
Caution:
Do not pinch the cable when sliding
the DISPLAY CONSOLE (K) onto the LEFT and
RIGHT UPRIGHTS (A) & (F).
7.
Tighten all SCREWS securely.
8.
Position the TREADMILL into the desired location
for use.
9.
Plug the TREADMILL into a proper electrical outlet
as instructed in SECTION 1.2 of this manual.
Содержание Essential FT4
Страница 1: ...FT4 Treadmill U S E R M A N U A L ...
