background image

HAL

 Operation manual 

 
This section describes  how to operate and use the bullfloat.In the text are numbers in brackets. 
These numbers are position numbers and they correspond to the numbers in the parts list of 
the corresponding figures. 
 
CAREFUL:  

Read the safety aspects and instructions before you switch on the apparatus. 

 
CAREFUL: 

Prevent the bullfloat of sinking into the concrete.After the motor has been switched  

 

 

on, immediately move the bullfloat backwards. 

 
TIP: 

 

Before the bullfloat is brought into action, first compact the freshly poured concrete 

 

 

floor with a poker-vibrator while at the same time adjust the height of the floor by  

 

 

means of a laser device. 

 
TIP: 

 

Pour concrete lanes of approx. 3 m. wide and approx. 15 m. long.You can finish this 

 

 

surface  in one pass without any problem. 

 

      

 

Type of switches. 
 
  

OPERATION OF THE BULLFLOAT , TYPE HAL200/E 

 
1  

Check that the bullfloat is properly assembled and make sure that the switch is in the  

   

OFF position. 

2  

Place the bullfloat in the direct vicinity of where you are going to smoothen the surface of 

    

the concrete. 

3  

Push the plug of the vibrating -unit’s feeder cable into the wall socket. 

4  

Place the bullfloat on the surface of the freshly poured concrete-floor. 

5  

Put the switch in the ON position. 

6  

Adjust the trowel blade angle. 

7  

Now start to smoothen the surface of the concrete-floor by moving  the bullfloat backwards in 

   

a slow but steady  motion. 

8  

After  having finished one lane of concrete, switch off the bullfloat immediately. 

 
TIP: 

If the processed  concrete-surface is not smooth or level enough, repeat the procedures 

      

5,6,7 and 8 . 

 
9  

Pull the feeder cable’s plug of the bullfloat out of the wall socket. 

10  

After use, place the bullfloat on a dry and stable surface. 

 
 
 
 
 
 

Содержание HAL B Honda






















Отзывы:

Похожие инструкции для HAL B Honda