background image

 

22

 

TROUBLESHOOTING GUIDE 

PROBLEM 

CAUSE 

SOLUTION 

UPS is short circuited or 
overloaded 

Ensure UPS is off.  Disconnect all loads 
and ensure nothing is lodged in output 
sockets.  Ensure loads are not defective 
or shorted internally. 

UPS fails to start 
when on button is 
pressed 

Internal fuse is blown, 
indicating internal fault 

Do not attempt to open or service the 
UPS.  Contact your dealer or LTS. 

UPS not plugged in 

UPS is operating from battery mode, 
make certain UPS is securely plugged 
into the wall socket 

UPS input protection has 
opened 

UPS is operating from battery mode.  
Save data and close applications.  
Replace UPS input fuse or reset input 
breaker, then restart UPS. 

Battery indicator is 
illuminated 

Utility voltage out of UPS 
input range. 

UPS is operating from battery mode.  
Save data and close applications.  
Ensure utility supply voltage is within 
acceptable limits for UPS. 

Batteries not fully charged 

Keep UPS plugged in continuously at 
least 24 hours to recharge batteries 

UPS is overloaded 

Check load level display and reduce load 
level 

UPS has reduced 
battery time 

Batteries may not be able to 
hold a full charge due to age 

Replace batteries.  Contact your dealer 
or LTS for replacement battery kit 

Fault and Bypass 
indicators and all load 
level LEDs are 
illuminated 

UPS overloaded or load 
equipment is faulty 

Check load level display and remove 
non-essential loads.  Recalculate load 
VA and reduce number of loads 
connected to UPS.  Check load 
equipment for faults. 

Fault and Bypass 
indicators and 
diagnostic LED A are 
illuminated 

UPS internal fan has a 
problem or UPS shutdown 
due to temperature condition.  
Load is on bypass power 

Ensure UPS is not overloaded, 
ventilation openings not blocked, or room 
ambient temperature not excessive.  
Wait 30 minutes to allow UPS to cool, 
then restart UPS.  IF it does not restart, 
contact your dealer or LTS. 

Fault and Bypass 
indicators and 
diagnostic LED B are 
illuminated 

UPS internal DC bus 
overvoltage 

UPS requires service.  Contact your 
dealer or LTS. 

Fault and Bypass 
indicators and 
diagnostic LED C are 
illuminated 

UPS power control fault. 

UPS requires service.  Contact your 
dealer or LTS. 

Fault and Bypass 
indicators and 
diagnostic LED D are 
illuminated 

UPS PFC fault. 

UPS requires service.  Contact your 
dealer or LTS. 

Fault and Bypass 
indicators and 
diagnostic LED E are 
illuminated 

UPS inverter fault. 

UPS requires service.  Contact your 
dealer or LTS. 

Fault and Bypass 
indicators and 
diagnostic LED A  & C 
are illuminated 

UPS failed the battery test. 

Replace batteries.  Contact your dealer 
or LTS. 

Fault and Bypass 
indicators and 
diagnostic LED C & E 
are illuminated 

UPS shutdown due to a 
command from the 
communications port(s) 

Your UPS has received a signal or 
command from the attached computer.  If 
this was inadvertent, ensure the 
communication cable used is correct for 
your system.  For assistance, contact 
your dealer or LTS. 

Содержание UPStation GXT





























Отзывы: