LI-COR LI-870 Скачать руководство пользователя страница 5

iii

Notes on Safety

This LI-COR product has been designed to be safe when operated in the manner described in this manual. The safety of
this product cannot be assured if the product is used in any other way than is specified in this manual. The product is
intended to be used by qualified personnel. Read this entire manual before using the product.

Equipment markings:

The product is marked with this symbol when it is necessary for you to refer to the manual or
accompanying documents in order to protect against injury or damage to the product.

The product is marked with this symbol when a hazardous voltage may be present.

The product is marked with this symbol if a Chassis Ground connection is required.

The product is marked with this symbol to indicate that a direct current (DC) power supply is
required.

WARNING

Warnings must be followed carefully to avoid bodily injury.

CAUTION

Cautions must be observed to avoid damage to your equipment.

Manual markings:

Warning

Warnings must be followed carefully to avoid bodily injury.

Caution

Cautions must be observed to avoid damage to your equipment.

Note

Notes contain important information and useful tips on the operation of your equipment.

CE Marking:

This product is a CE-marked product. For conformity information, contact LI-COR Support at [email protected].
Outside of the U.S., contact your local sales office or distributor.

California Proposition 65 Warning

WARNING:

This product contains chemicals known to the State of California to cause cancer and birth defects or other

reproductive harm.

Federal Communications Commission Radio Interference Statement

WARNING:

This equipment generates, uses, and can radiate radio frequency energy and if not installed in accordance

with the instruction manual, may cause interference to radio communications. It has been tested and found to comply
with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to
provide a reasonable protection against such interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the user, at his own expense, will be required
to take whatever measures may be required to correct the interference.

Содержание LI-870











































Отзывы: