LG XD3 25U Series Скачать руководство пользователя

Страница: 19 / 56

INSTALLATION

ENGLISH

• Use sealant tape or sealing compound on the

tap’s thread to avoid water leaks.

• Make sure that the line is not kinked or sharply

bent.

NOTE

• Before connecting the water supply hose to the

tap, turn on the tap to flush out foreign

substances (dirt, sand or sawdust) in the water

lines. Let water drain into a bucket.

• It takes about 3 – 4 minutes for the first supply

water.

Routing Electrical Wiring

Connect the appliance to an earthed socket in

accordance with the current wiring regulations,

protected by a minimum 15 amp circuit breaker or

time delay fuse.
Wiring must be two wires with earth.
The power cord should not be positioned behind

the appliance but within 1.2 meters of the side so

that the plug is easily accessible.

WARNING

• For personal safety, remove house fuse or open

circuit breaker or switch off power plug before

installation.

• Do not use an extension cord or double adapter.
• The plug must be plugged into an appropriate

outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

• Repairs to the appliance must only be carried out

by qualified service personnel. Repairs carried

out by inexperienced persons may cause injury

or serious malfunctioning. Contact our local

service centre.

• Connect to a properly rated, protected, and sized

power circuit to avoid electrical overload.

Final Installation Check

Testing the Dishwasher

Turn on electrical power.

Turn on house water supply.

The door should open and close smoothly and

without harsh noises, if the unit has been

levelled correctly.

Run the appliance on a

Rinse

cycle to verify

proper operation and check for leaks.

Installation Check Error Codes

Error

Code

Possible Cause and Solution

Drain hose kinked or pinched.

• Feed the drainage and supply

hoses through the hole under

the sink. Then gradually slide the

dishwasher into the cabinet

while pulling on the hoses under

the sink to take up any slack. This

helps avoid kinking the hoses or

trapping them beneath the

dishwasher.

Waste spigot under sink is

clogged.

• Drill out the waste spigot under

the sink.

Содержание XD3 25U Series

























































Результаты поиска

Содержание XD3 25U Series

Отзывы:

Похожие инструкции для XD3 25U Series

Бренды по названию

Популярные бренды

LG XD3 25U Series, Руководство пользователя

Результаты поиска

Содержание XD3 25U Series

Отзывы:

Похожие инструкции для XD3 25U Series

Бренды по названию

Популярные бренды