LG WT-R107 Скачать руководство пользователя

Страница: 38 / 55

4-6. TEST RUNNING WITHOUT WATER

To use the CHECK PROGRAM (QC TEST MODE), press WASH/RINSE, SPIN SPEED and POWER button
ON without depositing any laundry.
START(PAUSE) button to check over the following items.

CHECK METHOD

DISPLAY

CHECK ITEM

REMARKS

Initial state

Press once

Press twice

Press 3 times

Press 4 times

Press 5 times

Press 6 times

Press 7 times

Press 8 times

Press 10 times

Press 11 times

Load Value / t5

After detecting laundry amount ,
Spin ON.

Test Mode Start

t1/HA

Version/t2

Water Level Frequency / A

Water Level Frequency / b

All LEDS ON

ALL LEDS OFF

Chech each of buttons except

“Power” and “Start”

COLD Water ON. (Boost Dispenser,

Bleach Dispenser)

COLD Water ON. (Softener

Dispenser)

Water Level Frequency / C

Water Level Frequency / t4

Press 12 times

Press 14 times

Spin

COLD water and HOT Water ON.
(Detergent Dispenser)

DRAIN PUMP ON.

Ex) = 333 = 233
If there is no load it may
display above 300.

Press 13 times

Press 15 times

Error or nE / t7

Error

It display previous error.
If there is no error bofore it will
display “

”

RPM / t6

Press 16 times

OFF

ALL LEDS OFF

Press 9 times

1) METHOD TO USE QC TEST MODE

ALL LEDS OFF

Содержание WT-R107
























































Результаты поиска

Содержание WT-R107

Отзывы:

Похожие инструкции для WT-R107

Бренды по названию

Популярные бренды

LG WT-R107, Руководство по обслуживанию

Результаты поиска

Содержание WT-R107

Отзывы:

Похожие инструкции для WT-R107

Бренды по названию

Популярные бренды