LG WG1800R Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 31

background image

- 18 -

Copyright ©2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes

LGE Internal Use Only

4.3 TROUBLESHOOTING GUIDE

In general, possible trouble is classified in two causes.
The one is called Starting Failure which is caused from an electrical defect, and the other is Ineffective Air
Conditioning caused by a defect in the refrigeration circuit and improper application.

Unit runs but poor cooling

Ineffective Cooling

Check of outdoor coil
(heat exchanger) & the fan
operation.

Check gas leakage.

Repair gas leak.

Replacement of unit if the
unit is beyond repair.

Satisfactory operation with
temperature difference of
inlet & outlet air ; 44.6~50

°

F

Check heat load increase.

Unexpected residue

Overloaded Circuit

Check of inside gas
pressure.

Adjusting of refrigerant
charge

Malfunction of compressor

Replacement of
compressor

Check of cold air circulation
for smooth flow.

Dirty indoor coil
(Heat exchanger)

Malfunction of fan

Clogged of air filter

Obstruction at air outlet

Correct above trouble

Stop of auto air-swing

Check clogging in
refrigeration circuit.

Repair clogging in
refrigeration circuit.

«
...
16
17
18
19
20
...
»

Содержание WG1800R
































Отзывы:

Нет отзывов

Похожие инструкции для WG1800R

Бренд: Hamilton Beach Страницы: 2

Бренд: Zibro Страницы: 2

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 36

mini VRF U-4LE2R5

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 96

Бренд: Panasonic Страницы: 149

Бренд: Daikin Страницы: 84

AM TN4 KH Series

Бренд: Samsung Страницы: 40

Бренд: EdgeStar Страницы: 19

23-11-2194N-001 s

Бренд: Fedders Страницы: 34

Бренд: NEO TOOLS Страницы: 51

Бренд: koppel Страницы: 56

Бренд: Dimplex Страницы: 10

Бренд: DeDietrich Страницы: 12

Бренд: Vaporetto Страницы: 14

Бренд: Goodman Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды