LG WG1800R Скачать руководство пользователя страница 15

Страница: 15 / 31

- 15 -

LGE Internal Use Only

3.6 CABINET INSTALLATION

1. Open the window. Mark a line on the center of the window

stool between the side window stop moldings.
Loosely attach the sill bracket to the support bracket using
the carriage bolt and the lock nut.

2. Attach the sill bracket to the window sill using the screws

(Type B).
Carefully place the cabinet on the window stool and align the
center mark on the bottom front with the center line marked
window stool.

3. Using the M-screw and the lock nut, attach the support

bracket to the cabinet track hole. Use the first track hole
after the sill bracket on the outer edge of the window sill.
Tighten the carriage bolt and the lock nut. Be sure the
cabinet slants outward.

CAUTION: Do not drill a hole in the bottom pan. The unit is

designed to operate with approximately 1/2" of
water in bottom pan.

4. Pull the bottom window sash down behind the Top retainer

bar until they meet.

NOTE:

1. Do not pull the window sash down so tightly that the

movement of Frame curtain is restricted. Attach the
cabinet to the window stool by driving the screws
(Type B) through the cabinet into window stool.

2. The cabinet should be installed with a very slight tilt

downward toward the outside.

Support

Bracket

Lock nut

Sill

Bracket

Carriage

Bolt

(M-Screw)

Front angle

Window stool

Window sash

Top retainer bar

Cabinet

Foam-PE

Frame curtain

Screw(Type B)

Front Angle

Sash track

Foam-PE

Cabinet

Track hole

Support

Bracket

Carriage bolt

and lock nut

Machine screw (Type D)

and lock nut

Outer edge

of window

sill

Screw(Type B)

Sill bracket

Top
retainer
bar

Figure 22

Figure 23

Figure 24

Figure 25

Figure 26

Содержание WG1800R
































Результаты поиска

Содержание WG1800R

Отзывы:

Похожие инструкции для WG1800R

Бренды по названию

Популярные бренды

LG WG1800R, Руководство по обслуживанию

Результаты поиска

Содержание WG1800R

Отзывы:

Похожие инструкции для WG1800R

Бренды по названию

Популярные бренды