2
CAUTION: THESE SERVICING
INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY.
TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT PERFORM ANY
SERVICING OTHER THAN THAT
CONTAINED IN THE OPERATING
INSTRUCTIONS UNLESS YOU ARE
QUALIFIED TO DO SO.
Caution: The apparatus shoul
d not be
exposed to water (dripping or splashing)
and no objects filled with liquids, such as
vases, should be placed on the
apparatus.
CAUTION: This product employs a Laser
System.
To ensure proper use of this product,
please read this owner’s manual carefully
and retain for future reference. Should
the unit require maintenance, contact an
authorized service center.
Use of controls, adjustments, or the
performance of procedures other than
those specified herein may result in
hazardous radiation exposure.
To prevent direct exposure to laser beam,
do not try to open the enclosure. Visible
laser radiation when open. DO NOT
STARE INTO BEAM.
WARNING: Do not install this equipment in
a confined space such as a bookcase or
similar unit.
This product is manufactured to comply with
the radio interference requirements of EEC
DIRECTIVE 89/336/EEC, 93/68/EEC and
73/23/EEC.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a
dedicated circuit;
That is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch circuits.
Check the specification page of this owner's manual to be
certain.
Do not overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords, frayed
power cords, or damaged or cracked wire insulation are
dangerous. Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the appliance,
and have the cord replaced with an exact replacement part
by an authorized servicer.
Protect the power cord from physical or mechanical abuse,
such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets,
and the point where the cord exits the appliance.
SERIAL NUMBER:
You can find the serial number on the back of the unit.
This number is unique to this unit and not available to
others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No. ______________________________
Serial No. ______________________________
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
VIDEO Plus+ and PlusCode are registered
trademarks of Gemstar Development Corporation.
The VIDEO Plus+ system is manufactured under
license from Gemstar Development Corporation.
POWER:
This HDD/DVD Recorder operates on a mains
supply of 110-240V~, 50/60Hz.
WIRING:
This DVD & HDD Recorder is supplied with a BSI
1363 approved 13 amp mains plug, fused at 5 amp. When
replacing the fuse always use a 5 amp BS 1362, BSI or
ASTA approved type. Never use this plug with the fuse
cover omitted. To obtain a replacement fuse cover contact
your dealer. If the type of plug supplied is not suitable for the
mains sockets in your home, then the plug should be
removed and a suitable type fitted. Please refer to the wiring
instructions below:
WARNING:
A mains plug removed from the mains lead of
this DVD & HDD Recorder must be destroyed. A mains plug
with bared wires is hazardous if inserted in a mains socket.
Do not connect either wire to the earth pin, marked with the
letter E or with the earth symbol
or coloured green or
green and yellow.
If any other plug is fitted, use a 5 amp fuse, either in the
plug, or at the distribution board.
IMPORTANT:
The wires in this mains lead are coloured in
accordance with the following codes:
- BLUE: NEUTRAL, BROWN: LIVE -
As the colours of the
wires in the mains lead of this DVD & HDD Recorder may
not correspond with the coloured marking identifying the
terminals in your plug, proceed as follows: The wire which
is coloured blue must be connected to the terminal which is
marked with the letter N or coloured black. The wire which
is coloured brown must be connected to the terminal which
is marked with the letter L or coloured red.
