manualshive.com logo in svg

LG PBACNBTR0, Руководство по установке, Страница: 23 / 24

Поделиться
Скачать
LG PBACNBTR0 Скачать руководство пользователя страница 23

23

Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

TAB MOUNTING DIMENSIONS  

See Figure 11 for tab mounting dimensions for the MultiSITE Communications Manager controller. Measurements shown below are in inches 

and (mm). 

Figure 11: Tab mounting dimensions. 

1

 = MultiSITE Communications Manager controller. With no optional LON modules added, allow at least 1.5” (38mm) clearance around all 

sides, and minimum 3”(76mm) at bottom for WiFi antenna. 

2 

= Optional LON module. Up to four (4) may be used. 

3 

= Distances between center of tabs from one unit to another unit. 

Note:

DIN mounting is recommended over tab mounting. See “Mounting on DIN rail”.

4.33" 

(110)

    

6.38" (162)

    

7.05" (179)

0.34" (8.6)

0.165" 

Dia. 

(4.2)

3.31" 

(84)

3.31" 

(84)

    

 

1

2

2.44” (62)

LON

2.11” (53.5)

6.71” (170.5)

 

2.13

(54)

6.71”

(170.5)

3

Содержание PBACNBTR0

























Отзывы:

Нет отзывов