LG Panorama LFX21980ST Скачать руководство пользователя страница 7

Страница: 7 / 51

- 7 -

2) Press gasket into channels on the three remaining

sides of door.

3. Replace door frame cover

Starting at top of cover and working down, snap cover
back into door.

3-2 DOOR ALIGNMENT

If fridge door are uneven,

• Use the wrench (Included with the User Manual) to
adjust the bolt in the door hinge to adjust the
height.(CCW to raise or CW to lower the height.)

Figure 6

Figure 8

Figure 7

Figure 9

3-3 FAN AND FAN MOTOR(EVAPORATOR)

1. Remove the freezer shelf. (If your refrigerator has an

icemaker, remove the icemaker first)

2. Remove the plastic guide for slides on left side by

unscrewing phillips head screws.

3. Remove the grille by pulling the grille fan forward.
4. Remove the Fan Motor assembly by loosening 2 screws

and disassembling the shroud.

5. Pull out the fan and separate the Fan Motor and Bracket.

GRILLE

FAN MOTOR

FAN

BRACKET

MOTOR

Содержание Panorama LFX21980ST




















































Результаты поиска

Содержание Panorama LFX21980ST

Отзывы:

Похожие инструкции для Panorama LFX21980ST

Бренды по названию

Популярные бренды

LG Panorama LFX21980ST, Руководство по обслуживанию

Результаты поиска

Содержание Panorama LFX21980ST

Отзывы:

Похожие инструкции для Panorama LFX21980ST

Бренды по названию

Популярные бренды