background image

10

When using CD-ROM discs, CD-R discs, DVD discs or CD-RW discs, don’t attach any stickers
or labels to the discs. Using discs with them attached not only causes read and write errors, but
data on the disc may be lost due to damage to the disc itself.

DO NOT use non-standard discs. NON-standard discs may not play or store data properly. 

Emergency Eject

This drive has a feature that allows the CD to be ejected manually if necessary such as failure of
the drive or a power outage. 

NOTE:

Don’t use this feature 

except

in an emergency.

1) Turn the power to OFF.

2) Poke a fine-tipped object (such as a straightened heavy duty paper clip) into the small hole

above the eject button. The front door will pop open and the disk tray will come partway out.

3) Pull the front door to open it all the way, then grip the disc tray between thumb and forefin-

ger and gently pull it straight out.

*  If you cannot get a good grip on the disc tray with your fingers, use a steel binder clip or

spring clamp to pull it out.

How to Use the Discs

NOTE: 

This feature is a last measure to 

be used only in an emergency. 
Using it excessively will cause malfunction.

The Discs in this unit operate at a very high
speed! DO NOT use damaged, cracked or
warped discs. The drive’s optical unit may be
damaged if they break.

Содержание NeroPdvd
















Отзывы: