LG MULTI V LRNN-BE Series Скачать руководство пользователя страница 18

Страница: 18 / 19

Indoor Unit

Installation

You can choose the RPM(or air volume) of indoor
motor according to the height of ceiling to supply the
comfortable atmosphere to consumers.

Procedure

1. Choose the selectable position in the table after

measuring the height of ceiling.

2. In the case of changing the height as "high" or "low",

open the rear cover of the wired remote-control.

3. Move the slide switch to the set position.
4. Close the rear cover and check if it works nomally.

2) Adjusting air volume to the height of ceiling

R14H

SW TH

REMO

MAIN

2TH

OP7

R18H

R17H

OP6

STAND

HIGH

R03S

C070

R04S

R02S

R01S

OP3

OP2

OP1

R19H

R11H

R13H

R12H

OP5R16H

OP4

R15H

CO1H

STAND

Slide switch for ceiling height

Slide switch for 2 Thermistor

Standard

(Default)

Low ceiling

High Ceiling

Ceiling height

Mode of slide switch

Change of air volume

Remark

more than 4.0m

High Ceiling

Increasing

3.2~4.0m

Standard

less than 3.2m

Low Ceiling

Decreasing

Maunfactured in stan-

dard mode

1) Two Thermistor System

(1) Open the rear cover of the wired remote-control to set

the mode.

(2) Select one of three selectable modes as follows.

• Position 1:

The room temperature is controlled by the thermistor
of the main body.

• Position 2:

The room themperature is controlled by the thermis-
tor of the wired remote-control, control the tempera-
ture according to the position of wired remote-con-
trol.

• Position 3:

The room temperature is controlled by lower temper-
ature between the temperature of main body and of
remote-control sensor.

(3) Move the slide switch to set position.
(4) Close the rear cover and check if it works normally.

R14H

SW TH

REMO

MAIN

2TH

OP7

R18H

R17H

OP6

STAND

HIGH

R03S

C070

R04S

R02S

R01S

OP3

OP2

OP1

R19H

R11H

R13H

R12H

OP5R16H

OP4

R15H

CO1H

REMO

Room Temp. sensor

2TH

MAIN

Position 2

Position 1
Position 3

Slide switch for ceiling height

Slide switch for 2 Thermistor

Optional operation

CAUTION :

• Select the position after counselling with a customer.

In case of cooling mode, room temperature is controlled by the main body sensor.

• To control the room temperature by a wired remote control, install control(room

temp. sensor) to sense the temperature more accurately.

• Maunfactured in the position 3.

Содержание MULTI V LRNN-BE Series




















Результаты поиска

Содержание MULTI V LRNN-BE Series

Отзывы:

Похожие инструкции для MULTI V LRNN-BE Series

Бренды по названию

Популярные бренды

LG MULTI V LRNN-BE Series, Руководство по установке

Результаты поиска

Содержание MULTI V LRNN-BE Series

Отзывы:

Похожие инструкции для MULTI V LRNN-BE Series

Бренды по названию

Популярные бренды