background image

6

ENGLISH

SELECT THE BEST LOCATION

Select space for installing outside unit , which will meet the following
conditions:

• With strength which bears weight of unit

• With space for air passage and service work

Don't install the unit at the space where generation, inflow, stagna-
tion, and leak of combustible gas is expected.

• Avoid unit installation in a place where acidic solution and spray (sul-

fur) are often used.

• Location with no leakage of combustible gas

• Recommend the outside unit to be installed within 0~40°C.

• Location with installation or service work space (Refer to required

space)

• Do not use the outside unit under any special environment where oil,

steam and sulfuric gas exist. 

• Install in a separate machine room not exposed to external air

- Establish an anti-freeze plan for the water supply when the product
is stopped during the winter.
- Install the product so that the noise from the machine room is not
transferred outsides

• The floor of the machine room must be water proof.

• Drainage must be installed in the machine room to process the water

drainage. 

• Install a floor slope to make the drainage smooth. 

• Avoid installing the outside unit in the location with following condi-

tions.

• Location where corrosive gas such as acidic gas is generated. 

(It may cause the refrigerant leakage by corrosion of the pipe.)

• Location where electromagnetic waves happen. 

(It may cause the abnormal operation by control parts disorder.)

• Location to be able to leak the combustible gas

• Location with carbon fiber or combustible dust.

• Location with the combustible material like thinner or gasoline. 

(It may cause a fire by leaking the gas near the product.)

ALTERNATIVE REFRIGERANT R410A

The refrigerant R410A has the property of higher operating pressure in
comparison with R22.  
Therefore, all materials have the characteristics of higher resisting
pressure than R22 ones and this characteristic should be also consid-
ered during the installation. 
R410A is an azeotrope of R32 and R125 mixed at 50:50, so the ozone
depletion potential (ODP) of R410A is 0. 
These days the developed countries have approved it as the environ-
ment-friendly refrigerant and encouraged to use it widely to prevent
environment pollution.

CAUTION

• The wall thickness of the piping should comply with the relevant

local and national regulations for the designed pressure 3.8MPa

• Since R410A is a mixed refrigerant, the required additional

refrigerant must be charged in its liquid state. 
If the refrigerant is charged in its gaseous state, its composition
changes and the system will not work properly.

• Do not place the refrigerant container under the direct rays of

the sun to prevent it from exploding.

• For high-pressure refrigerant, any unapproved pipe must not be

used.

• Do not heat pipes more than necessary to prevent them from

softening.

• Be careful not to install wrongly to minimize economic loss

because it is expensive in comparison with R22.

!

CAUTION

• Do not install Multi V water outside. Always install indoor like

machine room.

• Inverter product may generate electric noise. Keep the body

from computer, stereo etc. at enough distance. Specially leave
space from indoor remote controller to shoes electric devices at
the above 3m in weak electric wave area. Insert the power
cable and other wire into separate conduit.

!

Unit

4 Unit

System Capacity (HP)

Model

Combination Unit

Independent Unit

Refrigerant Precharged Amount

kg

Maximum Connectable Number of Indoor Units

Net Weight  

kg  

lbs  

Dimensions(WxHxD)  

mm  
inch  

Refrigerant
Connecting Pipes  

Liquid   mm(inch)  
Gas  

mm(inch)  

Water Connect-
ing Pipes  

Inlet  

mm  

Outlet  

mm  

Drain Outlet

mm  

Temp. range of
Circulation water

Cooling
Heating

74

76

ARWN740LAS4

ARWN760LAS4

ARWN200LAS4

ARWN200LAS4

ARWN200LAS4

ARWN200LAS4

ARWN200LAS4

ARWN180LAS4

ARWN140LAS4

ARWN180LAS4

3.0 + 3.0 + 3.0 + 5.8

3.0 + 3.0 + 3.0 + 3.0

64

64

(140 x 3) + (127 x 1)

140 x 4

(309 x 3) + (280 x 1)

309 x 4

(755 × 997 × 500) x 4

(755 × 997 × 500) x 4

(29-23/32 x 39-1/4 x 19-11/16) x 4 (29-23/32 x 39-1/4 x 19-11/16) x 4

22.2(7/8)  

22.2(7/8)  

53.98(2-1/8)

53.98(2-1/8)

PT 40  + PT 40 + PT 40 + PT 40

PT 40  + PT 40 + PT 40 + PT 40

PT 40  + PT 40 + PT 40 + PT 40

PT 40  + PT 40 + PT 40 + PT 40

20

20

10°C ~ 45°C(50°F ~ 119°F)

10°C ~ 45°C(50°F ~ 120°F)

-5°C ~ 45°C(23°F ~ 119°F)

-5°C ~ 45°C(23°F ~ 120°F)

Unit

4 Unit

System Capacity (HP)

Model

Combination Unit

Independent Unit

Refrigerant Precharged Amount

kg

Maximum Connectable Number of Indoor Units

Net Weight  

kg  

lbs  

Dimensions(WxHxD)  

mm  
inch  

Refrigerant
Connecting Pipes  

Liquid   mm(inch)  
Gas  

mm(inch)  

Water Connect-
ing Pipes  

Inlet  

mm  

Outlet  

mm  

Drain Outlet

mm  

Temp. range of
Circulation water

Cooling
Heating

78

80

ARWN780LAS4

ARWN800LAS4

ARWN200LAS4

ARWN200LAS4

ARWN200LAS4

ARWN200LAS4

ARWN200LAS4

ARWN200LAS4

ARWN180LAS4

ARWN200LAS4

3.0 + 3.0 + 3.0 + 3.0

3.0 + 3.0 + 3.0 + 3.0

64

64

140 x 4

140 x 4

309 x 4

309 x 4

(755 × 997 × 500) x 4

(755 × 997 × 500) x 4

(29-23/32 x 39-1/4 x 19-11/16) x 4 (29-23/32 x 39-1/4 x 19-11/16) x 4

22.2(7/8)  

22.2(7/8)  

53.98(2-1/8)

53.98(2-1/8)

PT 40  + PT 40 + PT 40 + PT 40

PT 40  + PT 40 + PT 40 + PT 40

PT 40  + PT 40 + PT 40 + PT 40

PT 40  + PT 40 + PT 40 + PT 40

20

20

10°C ~ 45°C(50°F ~ 121°F)

10°C ~ 45°C(50°F ~ 122°F)

-5°C ~ 45°C(23°F ~ 121°F)

-5°C ~ 45°C(23°F ~ 122°F)

Unit

4 Unit

System Capacity (HP)

Model

Combination Unit

Independent Unit

Refrigerant Precharged Amount

kg

Maximum Connectable Number of Indoor Units

Net Weight  

kg  

lbs  

Dimensions(WxHxD)  

mm  
inch  

Refrigerant
Connecting Pipes  

Liquid   mm(inch)  
Gas  

mm(inch)  

Water Connect-
ing Pipes  

Inlet  

mm  

Outlet  

mm  

Drain Outlet

mm  

Temp. range of
Circulation water

Cooling
Heating

68

70

72

ARWN680LAS4

ARWN700LAS4

ARWN720LAS4

ARWN200LAS4

ARWN200LAS4

ARWN200LAS4

ARWN200LAS4

ARWN200LAS4

ARWN200LAS4

ARWN140LAS4

ARWN160LAS4

ARWN180LAS4

ARWN140LAS4

ARWN140LAS4

ARWN140LAS4

3.0 + 3.0 + 5.8 + 5.8

3.0 + 3.0 + 3.0 + 5.8

3.0 + 3.0 + 3.0 + 5.8

64

64

64

(140 x 2) + (127 x 2)

(140 x 3) + (127 x 1)

(140 x 3) + (127 x 1)

(309 x 2) + (280 x 2)

(309 x 3) + (280 x 1)

(309 x 3) + (280 x 1)

(755 × 997 × 500) x 4 (755 × 997 × 500) x 4 (755 × 997 × 500) x 4

(29-23/32 x 39-1/4 x 19-11/16) x 4 (29-23/32 x 39-1/4 x 19-11/16) x 4 (29-23/32 x 39-1/4 x 19-11/16) x 4

22.2(7/8)  

22.2(7/8)  

22.2(7/8)  

53.98(2-1/8)

53.98(2-1/8)

53.98(2-1/8)

PT 40  + PT 40 + PT 40 + PT40 PT 40  + PT 40 + PT 40 + PT40 PT 40  + PT 40 + PT 40 + PT40
PT 40  + PT 40 + PT 40 + PT40 PT 40  + PT 40 + PT 40 + PT40 PT 40  + PT 40 + PT 40 + PT40

20

20

20

10°C ~ 45°C(50°F ~ 116°F) 10°C ~ 45°C(50°F ~ 117°F) 10°C ~ 45°C(50°F ~ 118°F)

-5°C ~ 45°C(23°F ~ 116°F) -5°C ~ 45°C(23°F ~ 117°F) -5°C ~ 45°C(23°F ~ 118°F)

Содержание Multi V ARWN Series






































Отзывы: