LG multi V ARUN080BSS0 Скачать руководство пользователя страница 58

Страница: 58 / 75

ELECTRICAL WIRING

ENGLISH

Automatic Addressing

The address of indoor units would be set by Automatic Addressing

- Wait for 3 minutes after supplying power.

(IDU and ODU should be off)

- Press RED button of the outdoor units for 5 seconds. (SW01C)

- A “88” is indicated on 7-segment LED of the outdoor unit PCB.

- For completing addressing, 2~7 minutes are required depending on numbers of connected in-

door units

- Numbers of connected indoor units whose addressing is completed are indicated for 30 sec-

onds on 7-segment LED of the outdoor unit PCB

- After completing addressing, address of each indoor unit is indicated on the wired remote con-

trol display window. (CH01, CH02, CH03, ……, CH06 : Indicated as numbers of connected in-
door units)

[Heat Pump (MAIN PCB)]

DIP-SWITCH

7 - Segment

SW01C (

: confirm)

SW02C (

ඔ

: backward)

SW03C (

ඖ

: forward)

SW04C ( : cancel)

SW01D (reset)

CAUTION

• In replacement of the indoor unit PCB, always perform Automatic addressing setting again (At

that time, please check about using Independent power module to any indoor unit.)

• If power supply is not applied to the indoor unit, operation error occur.

• Automatic Addressing has to be performed after 3 minutes to improve communication.

1,MFL67798018,영영 2018. 6. 15. 영영 2:29 Page 58

Содержание multi V ARUN080BSS0












































































Результаты поиска

Содержание multi V ARUN080BSS0

Отзывы:

Похожие инструкции для multi V ARUN080BSS0

Бренды по названию

Популярные бренды

LG multi V ARUN080BSS0, Руководство по установке

Результаты поиска

Содержание multi V ARUN080BSS0

Отзывы:

Похожие инструкции для multi V ARUN080BSS0

Бренды по названию

Популярные бренды